Toyota iQ EV Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 34

background image

5. REMOVE INVERTER COVER ASSEMBLY

RH

(1) Remove the 3 clips and the inverter cover

assembly RH from the inverter with converter

assembly.

6. CHECK TERMINAL VOLTAGE (w/ Quick

Charging Inlet)

Caution:

Wear insulated gloves.

(1) Open the charge lid.

(2) Open the cap of the DC charger inlet cable.

(3) Using a voltmeter, measure the voltage of the

high voltage inlet terminal.

Standard voltage:

0 V

Hint:

Use measuring range of DC 750 V or more on the

voltmeter.

7. DISCONNECT

DC CHARGER INLET

CABLE (w/ Quick Charging Inlet)

Caution:

Wear insulated gloves.

(1) Using a screwdriver, move the 2 lock levers as

shown in the illustration and disconnect the 2

DC charger inlet cable connectors from the EV

charger wire.

Lock Lever

8. DISCONNECT EV CHARGER WIRE (w/

Quick Charging Inlet)

Caution:

Wear insulated gloves.

(1) Disengage the 2 clamps and disconnect the EV

charger wires from the wiring harness clamp

bracket.

22

«
...
23
24
25
26
27
...
»

Содержание iQ EV



































Отзывы:

Нет отзывов

Похожие инструкции для iQ EV

Бренд: AA Products Страницы: 8

Бренд: Warrior Winches Страницы: 17

Бренд: Metra Electronics Страницы: 2

Бренд: Alpine Страницы: 8

Бренд: Toyota Страницы: 371

Бренд: Mercedes-Benz Страницы: 54

Бренд: TAUBENREUTHER Страницы: 8

Бренд: Mazda Страницы: 122

Бренд: Icom Страницы: 20

Бренд: GMC Страницы: 120

Бренд: Prime Tech Страницы: 6

Бренд: Opel Страницы: 32

Бренд: Improved Racing Страницы: 17

Alloy Rugged Ridge X-Clamp

Бренд: Omix-Ada Страницы: 2

Бренд: Dodge Страницы: 3

Бренд: SpeedTech Lights Страницы: 2

Turnoverball 1020

Бренд: Bowers & Wilkins Страницы: 6

Бренд: Mazda Страницы: 196

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды