manualshive.com logo in svg

Toyota HILUX 'A' DECK, Инструкция по монтажу

Поделиться
Скачать
Toyota HILUX 'A' DECK Скачать руководство пользователя страница 11

25

25

34

34

10mm

916mm

TUB

TUB

TUB

20. One at a time, remove the backing papers from the anti-abrasive tape patches and apply to the tub as shown above
on the forward most past of the side rail. Repeat until all patches are applied. Smooth  out the patches to remove any air 
bubbles. 

Note:

 the small patches are applied at the front of the tub and large ones at the rear. Repeat for RHS. 

See Dia #20

. 

21. Remove the front and rear brackets and foot cups from the sports bar. Retain all the hardware. 

Note: Run M8 tap through sports bar mounting brackets. See Dia #21

.

Hard Tonneau Cover, A-Deck
Accessory Part No. PZQ70-89870  

TC0403c

Page 11 of 34

Accessory Part No. PZQ70-89870

ISSUE 4: 09/10/18

Diagram #20

A

A

19. Align lock striker bracket (10) to the holes position “A” on the LHS. NOTE: Striker side marked “B” must attach to the 
tub as shown. Place the support bracket (33) inside the tub and secure using M6 bolts, washers and nuts, (Torque 8Nm). 
Repeat for RHS. 

See Dia #19

.

Diagram #19

SIDE RAIL

SECTION VIEW

SECTION VIEWS

10

35

19

33

14

21

Diagram #21

B

“B” side up

TORQUE 8Nm

FRONT

T50

Содержание HILUX 'A' DECK

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды