background image

 

-

6

Hybrid Synergy Drive Component Locations & 
Descriptions 

 

Component 

Location 

Description 

12 Volt 

 

Auxiliary 
Battery  

Engine Compartment 
(2008 - 2010 Models) 
Cargo Area (2011 
Model) 

A lead-acid battery that supplies power to 
the low voltage devices.   

Hybrid 

 

Vehicle 
(HV) 
Battery 
Pack  

Cabin Area, Mounted 
to Cross Member 
under Second Row 
Seat 

288 Volt Nickel Metal Hydride (NiMH) 
battery pack consisting of 30 low voltage 
(9.6 Volt) modules connected in series.   

Power 

 

Cables  

Undercarriage and 
Engine Compartment  

Orange colored power cables carry high 
voltage Direct Current (DC) between the 
HV battery pack, inverter/converter, and 
A/C compressor.  These cables also carry 
3-phase Alternating Current (AC) 
between the inverter/converter, electric 
motors, and generator.   

Inverter/ 
Converter 

  

Engine Compartment   Boosts and inverts the high voltage 

electricity from the HV battery pack to 3-
phase AC electricity that drives the 
electric motors.  The inverter/converter 
also converts AC electricity from the 
electric generator and electric motors 
(regenerative braking) to DC that 
recharges the HV battery pack.   

Gasoline 

 

Engine   

Engine Compartment   Provides two functions:   

1) Powers vehicle.   
2) Powers generator to recharge the HV 
battery pack.   
The engine is started and stopped under 
control of the vehicle computer.   

Front 
Electric

 

Motor   

Engine Compartment   3-phase high voltage AC permanent 

magnet electric motor contained in the 
front transaxle.  It is used to power the 
front wheels. 

Electric 

 

Generator  

Engine Compartment   3-phase high voltage AC generator that is 

contained in the transaxle and recharges 
the HV battery pack.   

 
 
 
 
 

Hybrid Synergy Drive Components (2008 - 2010 Models) 

 

Hybrid Synergy Drive Components (2011 Model) 

 
 

 

 



Содержание Highlander 2008






































Отзывы: