Toyota ESM21 Скачать руководство пользователя страница 4

Страница: 4 / 55

Before use

I. Before use

Be sure to read this section before use

1. Important safety instructions

These safety instructions are designed to prevent danger or damage arising from the incorrect
operation of the machine. Read carefully and always follow the instructions.

Explanation of "

" and "

Symbol explanation

An incorrect operation could result in death or serious injury.

An incorrect operation could result in an injury or damage to the machine.

Do not touch

Prohibited actions

Required actions

Remove the power plug from the outlet.

Use an AC 220 to 230 V power source.

Not doing so could cause an electric shock or a fire.

220 to 230 V

Do not damage the power cord, modify it, bend it
excessively, jerk it or twist it.

Doing so could cause an electric shock or a fire.
If the power cord is damaged, it must be replaced by the
manufacturer or its service agent.

Do not operate where aerosol ( spray ) products are being used or where oxygen is
being administered.

Doing so could cause a fire.

Do not use outdoors.

Doing so could cause an electric shock or a fire.

Содержание ESM21
























































Результаты поиска

Содержание ESM21

Отзывы:

Похожие инструкции для ESM21

Бренды по названию

Популярные бренды

Toyota ESM21, Инструкция по эксплуатации

Результаты поиска

Содержание ESM21

Отзывы:

Похожие инструкции для ESM21

Бренды по названию

Популярные бренды