Toyota COROLLA2004, Электрическая схема проводки

Страница: 73 / 251

2004 COROLLA (EWD533U)
73
The current is always flowing from the HEAD MAIN fuse to HEAD relay (Coil side) to TERMINAL 6 of the daytime running
light relay, from ECU–B fuse to TERMINAL 3 of the daytime running light relay and from the TAIL fuse to TAIL relay (Coil
side) to TERMINAL 14 of the daytime running light relay (USA).
When the ignition SW is turned on, the current flowing through the GAUGE fuse flows to TERMINAL 12 of the daytime
running light relay.
1. Daytime Running Light Operation
When the engine is started, voltage generated at TERMINAL L of the generator is applied to TERMINAL 8 of the daytime
running light relay. If the parking brake lever is pulled up (Parking brake SW on) at this time, the relay is not activated so the
daytime running light system does not operate. If the parking brake lever is then released (Parking brake SW off), a signal is
input to TERMINAL 11 of the relay.
This activates the daytime running light relay and the HEAD relay is turned to on, so the current flows from the HEAD MAIN
fuse to the HEAD relay (Point side) to HEAD LH LWR, HEAD RH LWR fuses to TERMINAL 2 of the headlights to TERMINAL
1 to TERMINAL 1 of the daytime running light relay to TERMINAL 2 to GROUND, causing the headlights to light up
(Headlights light up dimmer than normal brightness.). Once the daytime running light system operates and the headlights
light up, the headlights remain on even if the parking brake lever is pulled up (Parking brake SW on).
If the engine stalls and the ignition SW remains on, the headlights remain light up even through current is no longer output
from TERMINAL L of the generator. If the ignition SW is then turned off, the headlights go off.
If the engine is started with the parking brake lever released (Parking brake SW off), the daytime running light system
operates and headlights light up when the engine starts.
2. Headlight Operation
When the light control SW is switched to Head position and the dimmer SW is set to Low position, causing the daytime
running light relay and the HEAD relay to turn on, so the current flows from the HEAD MAIN fuse to HEAD relay (Coil side) to
TERMINAL 6 of the daytime running light relay to TERMINAL 7 to TERMINAL 12 of the light control SW to TERMINAL 11 to
GROUND. The current to HEAD relay (Point side) then flows to HEAD LH LWR, HEAD RH LWR fuses to TERMINAL 2 of the
headlights (Low) to TERMINAL 1 to TERMINAL 1 of the daytime running light relay to TERMINAL 2 to GROUND, causing
the headlights to light up at normal intensity.
When the light control SW is switched to Head position and the dimmer SW is set to High position, the signal from the
dimmer SW is input to the daytime running light relay. This activates the daytime running light relay and the HEAD relay is
turned on, so the current flows from the HEAD MAIN fuse to HEAD relay (Point side) to TERMINAL 1 of the DIMMER relay to
TERMINAL 2 to TERMINAL 13 of the daytime running light relay, activating the DIMMER relay. This causes current to flow
from TERMINAL 3 of the DIMMER relay to TERMINAL 5 to HEAD LH UPR, HEAD RH–UPR fuses to TERMINAL 2 of the
headlights (High) to TERMINAL 1 to GROUND, causing the headlights to light up at high beam and the high beam indicator
light to light up.
When the dimmer SW is switched to Flash position, the signal from the dimmer SW is input to the daytime running light relay.
This activates the daytime running light relay and the HEAD relay is turned on, so the current flows from the HEAD MAIN
fuse to HEAD relay (Point side) to TERMINAL 1 of the DIMMER relay to TERMINAL 2 to TERMINAL 13 of the daytime
running light relay, activating the DIMMER relay, and also flows from the HEAD LH UPR, HEAD RH UPR fuses to
TERMINAL 2 of the headlights to TERMINAL 1 to GROUND, causing the headlights to light up at high beam and the high
beam indicator light to light up.
3. Automatic Light Control Operation (USA)
When the daytime running light is operating and the Automatic control sensor detects a decrease in the ambient light, the
automatic light control operation starts. At the same time, daytime running light relay is activated, so current flows from the
TAIL fuse to the TAIL relay (Coil side) to TERMINAL 14 of the daytime running light relay, and the HEAD MAIN fuse to the
HEAD relay (Coil side) to TERMINAL 6 of the daytime running light relay, activating both the TAIL relay and the HEAD relay,
so that the taillights and headlights light up.
When the automatic light control sensor detects an increase in the ambient light, the ignition SW is turned to off, the light
control SW is turned to Head position, and the automatic light control operation stops.
System Outline