Toyota Corolla 2008 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 310

background image

’08 Corolla_U (L/O 0706)

220

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

Before making these checks, make sure
you have followed the correct starting pro-
cedure given in “How to start the engine”
on page 206 in Section 3 and that you
have sufficient fuel. Also, check whether
the other keys will start the engine. If
they work, your key may be broken. Have
the key checked at your Toyota dealer. If
none of your keys work, there may be a
malfunction in the immobilizer system. Call
your Toyota dealer. (See “Keys” on page
10 in Section 1−2.)

If the engine is not turning over or is
turning over too slowly—

1. Check that the battery terminals are

tight and clean.

2. If the battery terminals are O.K., switch

on the interior light.

3. If the light is out, dim or goes out

when the starter is cranked, the battery
is discharged. You may try jump start-
ing. See “(c) Jump starting” on page
221 for further instructions.

If the light is O.K., but the engine still will
not start, it needs adjustment or repair.
Call a Toyota dealer or qualified repair
shop.

NOTICE

Do not pull− or push−start the ve-
hicle. It may damage the vehicle or
cause a collision when the engine
starts. Also the three−way catalytic
converter may overheat and become a
fire hazard.

If the engine turns over at its normal
speed but will not start—

1. Turn the ignition key to “ACC” or

“LOCK” and try starting the engine
again.

2. If the engine will not start, the engine

may be flooded because of repeated
cranking. See “(b) Starting a flooded
engine” on page 220 for further instruc-
tions.

3. If the engine still will not start, it needs

adjustment or repair. Call a Toyota
dealer or qualified repair shop.

If the engine will not start, your engine
may be flooded because of repeated
cranking.

If this happens, turn the key to “START”
with the accelerator pedal fully depressed.
Keep the key and accelerator pedal in
these positions for 15 seconds and re-
lease them. Then try starting the engine
with your foot off the accelerator pedal.

If the engine does not start after 15 sec-
onds of cranking, release the key, wait a
few minutes and try again.

If the engine still will not start, it needs
adjustment or repair. Call a Toyota dealer
or qualified repair shop for assistance.

NOTICE

Do not crank for more than 30 se-
conds at a time. This may overheat
the starter and wiring systems.

If your vehicle will not start—
(a) Simple checks

(b) Starting a flooded engine

«
...
44
45
46
47
48
...
»

Содержание Corolla 2008























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Corolla 2008

Бренд: VEAP SHIELD UNITED Страницы: 3

Бренд: Garmin Страницы: 2

Бренд: Warrior Products Страницы: 3

Бренд: Carefree Страницы: 12

Бренд: Mazda Страницы: 527

2008 Escalade EXT

Бренд: Cadillac Страницы: 496

Бренд: Suzuki Страницы: 353

Бренд: Torklift Страницы: 16

Бренд: BMW Страницы: 21

Бренд: Webasto Страницы: 18

Бренд: E&G Classics Страницы: 2

Бренд: Honda Страницы: 124

Бренд: Thule Страницы: 4

Бренд: MAcarbon Страницы: 3

MultiCharger 1204

Бренд: DEFA Страницы: 28

Бренд: Steelmate Страницы: 14

Бренд: Prorack Страницы: 14

Бренд: Ford Страницы: 256

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды