manualshive.com logo in svg

Toyota Corolla 2008, Руководство пользователя


Поделиться
Скачать
background image

’08 Corolla_U (L/O 0706)

221

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

To avoid serious personal injury and
damage to your vehicle which might re-
sult from battery explosion, acid burns,
electrical burns, or damaged electronic
components, these instructions must be
followed precisely.

If you are unsure about how to follow this
procedure, we strongly recommend that
you seek the help of a competent me-
chanic or towing service.

CAUTION

Batteries contain sulfuric acid
which is poisonous and corrosive.
Wear protective safety glasses when
jump starting, and avoid spilling
acid on your skin, clothing, or ve-
hicle.

If you should accidentally get acid
on yourself or in your eyes, remove
any contaminated clothing and flush
the affected area with water imme-
diately. Then get immediate medical
attention. If possible, continue to
apply water with a sponge or cloth
while en route to the medical office.

The gas normally produced by a
battery will explode if a flame or
spark is brought near. Use only
standardized jumper cables and do
not smoke or light a match while
jump starting.

NOTICE

The battery used for boosting must
be 12 V. Do not jump start unless you
are sure that the booster battery is
correct.

JUMP STARTING PROCEDURE

1. If the booster battery is installed in

another vehicle, make sure the vehicles
are not touching. Turn off all unneces-
sary lights and accessories.

When boosting, use the battery of
matching or higher quality. Any other
battery may be difficult to jump start
with.

If jump starting is difficult, charge the
battery for several minutes.

2. If required, remove all the vent plugs

from the booster and discharged batter-
ies. Lay a cloth over the open vents
on the batteries. (This helps reduce the
explosion hazard, personal injuries and
burns.)

3. If the engine in the vehicle with the

booster battery is not running, start it
and let it run for a few minutes. During
jump starting, run the engine at about
2000 rpm with the accelerator pedal
lightly depressed.

(c) Jump starting

Содержание Corolla 2008























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Corolla 2008

Uebler F42 Mounting And Operating Instructions preview
F42
Бренд: Uebler Страницы: 18
Lincoln 2015 MKS Owner'S Manual preview
2015 MKS
Бренд: Lincoln Страницы: 424
Volkswagen 1983 Camper Onwers Manual preview
1983 Camper
Бренд: Volkswagen Страницы: 26
FORM FIT SD 13R07-5 Installation Instructions preview
SD 13R07-5
Бренд: FORM FIT Страницы: 2
Thule Edge Flush Rail Instructions Manual preview
Edge Flush Rail
Бренд: Thule Страницы: 12
Caltrend CV445 Installation Instructions preview
CV445
Бренд: Caltrend Страницы: 2
Audiovox EM-2201 Installation Instructions preview
EM-2201
Бренд: Audiovox Страницы: 1
EGR EGR-3PVE-COLOUR Installation Instructions Manual preview
EGR-3PVE-COLOUR
Бренд: EGR Страницы: 28
Camoplast Polaris TATOU 4S Installation Manuallines preview
Polaris TATOU 4S
Бренд: Camoplast Страницы: 13
FALCON RIDGE Bobcat 3400 Instructions For Installation And Care preview
Bobcat 3400
Бренд: FALCON RIDGE Страницы: 4
BrandMotion FLTW-7511 Installation Manual preview
FLTW-7511
Бренд: BrandMotion Страницы: 6
POOL-LINE 110085 Assembly Instructions preview
110085
Бренд: POOL-LINE Страницы: 2
Prorack K623 Fitting Instructions Manual preview
K623
Бренд: Prorack Страницы: 15
Acura RLX 2016 Service Bulletin preview
RLX 2016
Бренд: Acura Страницы: 7
Metra Electronics 99-6510 User Manual preview
99-6510
Бренд: Metra Electronics Страницы: 17
Cadillac 1967 Calais Coupe Data Book preview
1967 Calais Coupe
Бренд: Cadillac Страницы: 255
Gold Lantern GL-VTMK20 Specifications preview
GL-VTMK20
Бренд: Gold Lantern Страницы: 1
Metec 806255 Mounting Instructions preview
806255
Бренд: Metec Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды