manualshive.com logo in svg

Toyota Corolla 2008, Руководство пользователя


Поделиться
Скачать
background image

’08 Corolla_U (L/O 0706)

273

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

TIRE CHAIN SELECTION

Use the tire chains of correct size and
type.

Use SAE Class “S” type radial tire chains
except radial cable chains or V−bar type
chains.

Regulations regarding the use of tire
chains vary according to location or
type of road, so always check local reg-
ulations before installing chains.

CHAIN INSTALLATION

Install the chains on the front tires as
tightly as possible. Do not use tire
chains on the rear tires. Retighten
chains after driving 0.5—1.0 km
(1/4—1/2 mile).

When installing chains on your tires, care-
fully follow the instructions of the chain
manufacturer.

If wheel covers are used, they will be
scratched by the chain band, so remove
the covers before putting on the chains.

CAUTION

Do not exceed 50 km/h (30 mph) or
the chain manufacturer’s recom-
mended speed limit, whichever is
lower.

Drive carefully avoiding bumps,
holes, and sharp turns, which may
cause the vehicle to bounce.

Avoid sharp turns or locked−wheel
braking, as use of chains may ad-
versely affect vehicle handling.

When driving with chains installed,
be sure to drive carefully. Slow
down before entering curves to
avoid losing control of the vehicle.
Otherwise an accident may occur.

NOTICE

Do not attempt  to use a tire chain on
the compact spare tire, as it may re-
sult in damage to the vehicle as well
as the tire.

As you might have difficulty in identify-
ing a flat or deflated tire, a tire pres-
sure warning system is provided on
this vehicle.

When replacing the wheels, be sure to
install tire pressure warning valves and
transmitters on the wheels. Consult your
Toyota dealer about how to set up the tire
pressure warning valves and transmitters.

CAUTION

Have the tires, wheels or tire pres-
sure warning valves and transmit-
ters replaced and ID codes regis-
tered by Toyota dealer. If you need
tire pressure warning valves and
transmitters, purchase from Toyota
dealer.

The tire pressure warning valve and
transmitter nuts should always be
tightened to a torque of 4 N·m (0.4
kgf·m, 2.9 ft·lbf).

The use of non−genuine wheels may
result in the system failure or air−
leak.

Replacing wheels

Содержание Corolla 2008























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Corolla 2008

Accel 2020 Installation Instructions preview
2020
Бренд: Accel Страницы: 2
FORM FIT HDW 1779 Installation Instructions preview
HDW 1779
Бренд: FORM FIT Страницы: 2
Brodit ProClip 853660 Manual preview
ProClip 853660
Бренд: Brodit Страницы: 2
Power Fist 8985988 Manual preview
8985988
Бренд: Power Fist Страницы: 12
EAL EUFAB 16491 Operating Instructions Manual preview
EUFAB 16491
Бренд: EAL Страницы: 7
Havis-Shields 1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28 Install Instructions preview
1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28
Бренд: Havis-Shields Страницы: 3
Yakima K674 Instructions Manual preview
K674
Бренд: Yakima Страницы: 13
Menabo 000081000000, Fitting Instructions Manual preview
000081000000,
Бренд: Menabo Страницы: 11
Phonocar VM350 Mounting Instructions preview
VM350
Бренд: Phonocar Страницы: 2
Globalsat MR-350P Installation Manual preview
MR-350P
Бренд: Globalsat Страницы: 2
Inbay 241170-53-1 Installation Manual preview
241170-53-1
Бренд: Inbay Страницы: 20
JKS OGS125 Installation Instructions preview
OGS125
Бренд: JKS Страницы: 3
Metra Electronics 99-7477 Installation Instructions preview
99-7477
Бренд: Metra Electronics Страницы: 2
ULTIMATE SPEED 304669 Instructions For Use And Safety Manuallines preview
304669
Бренд: ULTIMATE SPEED Страницы: 50
Magneti Marelli 350203061230 Installation Instruction preview
350203061230
Бренд: Magneti Marelli Страницы: 2
Yakima LowRider Manual preview
LowRider
Бренд: Yakima Страницы: 15
Mercedes-Benz Sprinter 2003 Manual preview
Sprinter 2003
Бренд: Mercedes-Benz Страницы: 296
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Бренд: Oldsmobile Страницы: 380

Бренды по названию

Популярные бренды

Загрузить еще бренды