manualshive.com logo in svg

Toyota Corolla 2008, Руководство пользователя


Поделиться
Скачать
background image

’08 Corolla_U (L/O 0706)

266

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

If the level is low, add SAE J1703 or
FMVSS No.116 DOT 3 brake fluid to the
brake reservoir.

Remove and replace the reservoir cap by
hand. Fill the brake fluid to the dotted
line. This brings the fluid to the correct
level when you put the cap back on.

Use only newly opened brake fluid. Once
opened, brake fluid absorbs moisture from
the air, and excess moisture can cause a
dangerous loss of braking.

CAUTION

Take care when filling the reservoir
because brake fluid can harm your
hands or eyes. If fluid gets on your
hands or in your eyes, flush the af-
fected area with clean water immedi-
ately. If you still feel uncomfortable
with your hands or eyes, go to the
doctor.

NOTICE

If you spill some of the fluid, be sure
to wipe it off to prevent it from dam-
aging the parts or paintwork.

If cold O.K.

If cold add

If hot O.K.

If hot add

Close

Open

Check the fluid level through the reser-
voir. If necessary, add automatic trans-
mission fluid DEXRON

  II or  III.

If the vehicle has been driven around 80
km/h (50 mph) for 20 minutes (a little
more in frigid temperatures), the fluid is
hot (60

C—80

C or 140

F—175

F). You

may also check the level when the fluid
is cold (about room temperature,
10

C—30

C or 50

F—85

F) if the engine

has not been run for about five hours.

Clean all dirt from the outside of the res-
ervoir tank and look at the fluid level. If
the fluid is cold, the level should be in the
“COLD” range. Similarly, if it is hot, the
fluid level should be in the “HOT” range.
If the level is at the low side of either
range, add automatic transmission fluid
DEXRON

 II or III to bring the level within

the range.

To remove the reservoir cap, turn it coun-
terclockwise and lift up. To reinstall it,
turn it clockwise. After replacing the reser-
voir cap, visually check the steering box
case, vane pump and hose connections
for leaks or damage.

CAUTION

The reservoir tank may be hot so be
careful not to burn yourself.

NOTICE

Avoid overfilling, or the power steer-
ing could be damaged.

Checking power steering fluid

Содержание Corolla 2008























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Corolla 2008

JETBAG 320 Fitting Instructions Manual preview
320
Бренд: JETBAG Страницы: 44
Whispbar K783W Fitting Instructions Manual preview
K783W
Бренд: Whispbar Страницы: 16
Whispbar K925W Fitting Instructions Manual preview
K925W
Бренд: Whispbar Страницы: 15
Edelbrock 6883 Instructions preview
6883
Бренд: Edelbrock Страницы: 2
BGS technic 40108 Manual preview
40108
Бренд: BGS technic Страницы: 5
Oldsmobile 1999 88 Owner'S Manual preview
1999 88
Бренд: Oldsmobile Страницы: 344
ABL eMH3 Installation Manual preview
eMH3
Бренд: ABL Страницы: 66
Subaru 2016 Outback Owner'S Manual preview
2016 Outback
Бренд: Subaru Страницы: 99
Mercedes-Benz AMG E-Class Supplement Manual preview
AMG E-Class
Бренд: Mercedes-Benz Страницы: 54
aci ADARAC Aluminum M Series Installation Instructions Manual preview
ADARAC Aluminum M Series
Бренд: aci Страницы: 16
Imiola HAK-POL O/018 Quick Manual preview
O/018
Бренд: Imiola HAK-POL Страницы: 3
ULTIMATE SPEED 91449 Operation And Safety Notes preview
91449
Бренд: ULTIMATE SPEED Страницы: 34
ULTIMATE SPEED 285690 Assembly And Safety Advice preview
285690
Бренд: ULTIMATE SPEED Страницы: 10
Rugged Ridge 11232.20 Quick Start Manual preview
11232.20
Бренд: Rugged Ridge Страницы: 2
Aries 2051182 Installation Manual preview
2051182
Бренд: Aries Страницы: 3
Mazda 2014 CX-9 User Manual preview
2014 CX-9
Бренд: Mazda Страницы: 604
Hama 00046080 Instructions For Use preview
00046080
Бренд: Hama Страницы: 2
Saleen 10-8002-C12167A Installation Manual preview
10-8002-C12167A
Бренд: Saleen Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды