background image

Page 12  of 16

  

 

 

 

 

 

              FR-S 2015   

   

 

 

    XM Satellite Radio     

PAIRING THE DEVICE:

1. Access the Bluetooth® Streaming Audio source 
in the vehicle's radio.  

2.  Press the "Connect" button to display the 
paired device list.

3. Select the “Yes" button to add the new device.  
At this point the radio will enter discoverable 
mode, allowing the Streaming Bluetooth® 
Satellite Radio device to connect.

4.  Locate the pairing button for the Bluetooth® 
Satellite Radio Device in the vehicle's glove 
compartment.
  

1.  PRESS and HOLD the pairing button for 

about 3 seconds.  The Status Indicator 

LED will start flashing RED quickly, 

indicating the pairing procedure has 
started.   

2. 

Release the button when it starts to flash 

RED quickly. 

3. 

The LED will start to flash GREEN quickly, 

indicating that it is connecting with the 
radio.   

4. 

Finally, the LED will begin to slowly flash 

GREEN to indicate that it has successfully 
paired to the vehicle's radio.

5. "SiriusXM" will now display on the paired 
device list.  Select the SiriusXM icon to select the 
device.

  Source  

Bluetooth Audio

  Connect  

Audio player is not connected

  Source  

Connect Audio Player

  Yes  

There are no audio players registered.

Would you like to add one now?

    

  No  

 Connect Bluetooth 

  Cancel

    

Registration Waiting 

Please operate the device to register it.

Device Name      : CAR MULTIMEDIA

Device Address  : 1C994C838B782

Passcode              : 0000

Select "Yes" to 

Add Device 

Select to 

Connect

Device 

Pairing Button

Status Indicator LED

 Connect Audio Player

Add New

    

    

        SiriusXM

Select 

SiriusXM

Southeast Toyota Distributors, LLC

Содержание 00016-00950

















Отзывы: