TOX PRESSOTECHNIK TOX-FinePress PFL 002 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 72

background image

Troubleshooting

50

TOX_Manual_FinePress_PFS-PFL-PFW_en

9.2

Detecting faults

If the press is equipped with a control system, the faults or warnings on the
central control unit are displayed and described.

Fault

Cause

Measures

The ram does not ex-
tend.

There is a mechanical fault on the
guide.

Contact authorized service personnel.

Power stroke does not
initiate

Insufficient air pressure

Check the air pressure.

Pneumatic line on cylinder is de-
fective

Contact authorized service personnel.

Mechanical defect on pneumatic
cylinder

Contact authorized service personnel.

Fault on control system

Contact authorized service personnel.

The nominal force not
reached.

There is a mechanical fault on the
guide.

Contact authorized service personnel.

The press head is not adequately
fastened.

Tighten the fastening screws evenly. Observe
the tightening torques, see:

Inspecting the fas-

tening of the press head, Page 57

«
...
48
49
50
51
52
...
»

Содержание TOX-FinePress PFL 002









































































Отзывы:

Нет отзывов

Похожие инструкции для TOX-FinePress PFL 002

Бренд: Cairox Страницы: 8

Бренд: Wacker Neuson Страницы: 54

Бренд: Gates Страницы: 36

Бренд: SAMCHULLY Страницы: 32

Бренд: MACROZA Страницы: 13

Бренд: Palmgren Страницы: 20

Бренд: Grizzly Страницы: 44

Бренд: Sealey Страницы: 3

Бренд: Stihl Страницы: 20

Бренд: Nova Electronics Страницы: 2

Бренд: Stanley Страницы: 233

Бренд: SAES Страницы: 9

Бренд: Yokota Страницы: 7

ILUEST NE Series

Бренд: Salicru Страницы: 60

Бренд: FACHOWIEC Страницы: 4

Бренд: FOR-A Страницы: 10

PowerPak 2.5X2 ECO

Бренд: PowerBox Systems Страницы: 12

Бренд: Omron Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды