manualshive.com logo in svg

Tower Hobbies RYAN STA, Инструкция по эксплуатации

Поделиться
Скачать
Tower Hobbies RYAN STA Скачать руководство пользователя страница 8

8

❏

 21. Use 6-minute epoxy to glue the nylon wing dowel in 

the leading edge of the wing.

Return to step 1 and install the aileron servo in the left wing.

Join the Wing Panels

❏

  1. Use 6-minute epoxy to glue the two plywood wing 

joiners together.

❏

 2. Without glue, insert the plywood wing joiner in one wing 

half and test fi t the wing halves together to check the fi t. Make 
sure both wing halves fi t together at the root without any 
gaps. If needed, slightly sand the wing joiner for the best fi t.

❏

 3. Gather everything needed to glue the two wing halves 

together including 30-minute epoxy, mixing sticks, mixing 
cup, epoxy brush, rubberbands, masking tape, 12" [305mm] 
long wire or small diameter dowel, denatured alcohol, paper 
towels and the two ¼-20 wing bolts from the parts bag.

❏

 4. Mix 2 oz. [59.1cc] of 30-minute epoxy. Working quickly, 

pour a generous amount into the joiner pocket of one wing 
half. Use the wire or dowel to thoroughly distribute the epoxy, 
coating all surfaces inside the joiner pocket. Coat the root rib 
and one half of the wing joiner. Insert the wing joiner in the 

wing. Coat the joiner pocket in the other wing half and the 

other end of the wing joiner. Join the wing halves together. 
Use the rubberbands to hold the trailing edges of the wing 
together using the wing bolts and leading edge dowels. 
Stand the wing up on end and use paper towels dampened 

with denatured alcohol to remove the excess epoxy that 

squeezes out. Use masking tape to hold the wing halves in 
alignment if necessary.

❏

 5. After the epoxy cures, remove the rubberbands and 

masking tape.

Install the Landing Gear

❏

 1. Trim the covering from over the slots for the right main 

landing gear.

Содержание RYAN STA

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды