Tower Hobbies Razor 3D Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 28

background image

6

BUILDING INSTRUCTIONS

ORDERING REPLACEMENT PARTS

Replacement parts for the Razor 3D ARF are available from
Tower Hobbies or Hobby Services using the order numbers
in the

Replacement Parts List

that follows. Contact Tower

at www.towerhobbies.com, or call toll free (800) 637-6050.
Contact Hobby Services by calling (217) 398-0007, or via
facsimile at (217) 398-7721. If ordering via fax, include a Visa

®

or MasterCard

®

number and expiration date for payment.

Mail parts orders and payments by personal check to:

Hobby Services

3002 N Apollo Drive, Suite 1
Champaign IL 61822

Be certain to specify the order number exactly as listed in the

Replacement Parts List

. Payment by credit card or personal

check only; no C.O.D.

If additional assistance is required for any reason contact
Product Support by e-mail at productsupport@towerhobbies.
com, or by telephone at (217) 398-8970.

REPLACEMENT PARTS LIST

Order No. Description

REPLACEMENT PARTS LIST

Fuse Set Tower Razor 3D ARF
Wing Tower Razor 3D ARF
Tail Set Tower Razor 3D ARF
Canopy Tower Razor 3D ARF
Landing Gear Tower Razor 3D ARF
Wheel Pants Tower Razor 3D ARF
Cowl Tower Razor 3D ARF
Decal Set Tower Razor 3D ARF

TOWA6040
TOWA6041
TOWA6042
TOWA6043
TOWA6044
TOWA6045
TOWA6046
TOWA6047

BUILDING INSTRUCTIONS ––––––––––––

PREPARATIONS

❏

1. If you have not done so already, remove the major parts of the

kit from the box and inspect for damage. If any parts are damaged
or missing, contact Product Support at the address or telephone
number listed in the “Kit Inspection” section on page 5.

❏

2. Carefully remove the tape and separate all the control

surfaces. Use a covering iron with a covering sock on high heat
to tighten the covering if necessary. Apply pressure over sheeted
areas to

thoroughly

bond the covering to the wood.

BUILD THE WING ––––––––––––––––––––––

INSTALL THE AILERONS

Drill a 3/32" [2.4mm] hole

1/2" [13mm] deep, in the center

of the hinge slot.

Cut the covering

away from the slot.

❏

1. Drill a 3/32" [2.4mm] hole 1/2" [13mm] deep into the

center of each hinge slot in the

ailerons

and

wing

. Trim the

covering away from each hinge slot to ensure that the hinges
will be properly glued in place.

«
...
4
5
6
7
8
...
»

Содержание Razor 3D





























Отзывы:

Нет отзывов

Похожие инструкции для Razor 3D

Build-a-ma-Jigs Racetruck BX1221

Бренд: B Страницы: 2

Бренд: HOBBY ENGINE Страницы: 8

Battleship Tirpitz

Бренд: REVELL Страницы: 30

BATTERY BUS, SETRA S 315

Бренд: Faller Страницы: 2

Бренд: GREAT PLANES Страницы: 50

Бренд: Fisher-Price Страницы: 20

MESSERSCHMITT BF 110 C

Бренд: Flying Styro Kit Страницы: 16

Бренд: Multiplex Страницы: 36

Бренд: C&C Models Страницы: 23

Jimmy Neutron boy genius ultra orb

Бренд: Radio Shack Страницы: 8

Бренд: EScale Страницы: 16

Бренд: Eduard Страницы: 6

imaginext J2532

Бренд: Fisher-Price Страницы: 12

TRACKMASTER T0787

Бренд: Fisher-Price Страницы: 1

Бренд: Oregon Scientific Страницы: 32

VisionAire AS3X

Бренд: PARKZONE Страницы: 20

Бренд: EXHOBBY Страницы: 16

Бренд: marklin Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды