Tower Hobbies P-51D Mustang Скачать руководство пользователя страница 8

Страница: 8 / 12

INST

ALL THE PROPELLER AND SPINNER

❏

Assemble the tailwheel as shown. Screw the set screw

into the tailwheel guide. Slide the tailwheel guide onto the
tailwheel post and tighten the set screw against the

at spot on

the tailwheel post.

❏

Remove the tailwheel retainer. Install the tailwheel assembly

to the fuselage and the tailwheel guide into the hole in the bottom
of the rudder. Reinstall the tailwheel retainer.

INSTALL THE PROPELLER AND SPINNER

❏

Remove the prop nut and prop washer from the prop

adapter. Slide the prop adapter onto the motor shaft as shown.

❏

Fit the spinner backplate to the prop adapter. Fit the

propeller, prop washer, and prop nut. Position the propeller so
that the trailing edge of each blade touches the alignment pin.

Tighten the prop nut.

❏

Install the spinner using the two screws included in the

spinner parts bag.

GET THE MODEL READY TO FLY

Check the Controls & Control Direction

WARNING:

Once the battery is connected to the ESC, stay clear

of the propeller! Always stay behind the propeller!

❏

Turn on the transmitter, center the trims, and move the

throttle stick all the way down. Attach a charged battery.

❏

With the transmitter and receiver still on, check to make

sure that all of the control surfaces are correctly centered so that
they are at zero de

ection. Check to see that the locking screws

on the pushrod connectors are tight and that the servo arm locking
screws are installed. Make sure that the nylon Faslinks are also
installed properly and are holding the pushrods securely.

Содержание P-51D Mustang













Результаты поиска

Содержание P-51D Mustang

Отзывы:

Похожие инструкции для P-51D Mustang

Бренды по названию

Популярные бренды

Tower Hobbies P-51D Mustang, Инструкция по эксплуатации

Результаты поиска

Содержание P-51D Mustang

Отзывы:

Похожие инструкции для P-51D Mustang

Бренды по названию

Популярные бренды