manualshive.com logo in svg

tousek PULL TSA, Руководство по монтажу и установке, Страница: 12 / 28

Поделиться
Скачать
tousek PULL TSA Скачать руководство пользователя страница 12

- 12 - 

tousek

  /  EN_PULL-TSA_03  /  25. 03. 2020

WARNING:Always follow the warning notes listed on page 9! 

 

Integrated radio receiver 

RS 868, 2-channel

•  The integrated radio receiver is provided with a  self-learning technology, ie the 

coding of the transmitter is learned into the receiver.

•  Every time that a command  is given, the coding gets altered by the transmitter 

(rolling code). Thanks to this permanent change, each code is used only once 

and thus an abusive use of the code by scanning is excluded. 

•  The receiver memory can store max. 48 transmitters. This means that all the 

buttons which are programmed with  the function „impulse“ or „partial opening“get 

stored under the same number. 

IMPORTANT: Make note of the numbers 

shown on the display during programming procedure!

•  When the receiver memory is full by any attempt of programming a transmitter 

button,  3 sec. long and  consecutive beeps are emitted.

 Antenna

•  An 8.5cm long piece of wire at  the terminal strip (A) is connected 

to the antenna pole connection of the receiver.

•  Do not  change the length of this piece of wire (loss of range)!!

•  In order to achieve longer range the antenna FK 868 is optionally 

available.

Antenna FK 868

(optional)

3.3  Connections and adjustments  

Sliding gate opener PULL TSA

Radio 

Connections and adjustments

 

P0

 Radio 

Buttons/ switches

o

  

 

learn impulse:

 After confirming by pressing the  

ENTER button,  the transmitter emits a continuous 

tone of approx. 10 sec.Press the transmitter buttons 

that have to be programmed within these 10 seconds. 

The successful storage process is signaled by a 

rapid succession of tones. 

Important: Make a note of 

the memory position / number shown on the display  

(needed for deleting process).   

transmitter list page 26.

 

SUGGESTION: with the function „pro-

gramm impulse transmitter“ you can also 

see on the display the position of an already 

memorized transmitter. When you hear a 

continuous tone press the  button P3, loca-

ted on the back side of the remote control 

(eg with a paper clip.)

1

  

 

learn partial opening:

 After confirming by pressing 

the  ENTER button,  the transmitter emits a continuous 

tone of approx. 10 sec. Press the transmitter buttons 

that have to be programmed for the partial opening 

within these 10 seconds. The successful storage 

process is signaled by a rapid succession of tones.  

Important: Make a note of the memory position / 

number shown on the display (needed for deleting 

process).   

page 26.

2

  

 

Delete individual transmitter: 

After selecting with the ENTER key, the occupied memory locations are displayed. 

Scroll through with the b - through this list until the memory location (number) displays the desired hand-held 

transmitter. With confirmation by the ENTER button of the remote control in question is completely extinguished, ie 

all programmed keys of the remote control.

3

  

 

delete all: 

 

  

 

NO: do not delete the transmitters

.

 

   

 

   

 

YES: all the programmed remote controls get deleted after confirming with  

 Enter.

FE

A

z.B.

innerhalb  

10 Sekunden !

Enter

1

Learn partial opening:

P3

z.B.

innerhalb  

10 Sekunden !

Enter

o

Learn impulse:

Determine memory position 

of an already memorized 

transmitter:

Backside of the 

transmitter

Содержание PULL TSA





























Отзывы:

Нет отзывов