tousek 12111670 Скачать руководство пользователя страница 24

Страница: 24 / 32

- 24 -

tousek

/ E_ST61_07 / 06. 06. 2019

Important: preparation works

• Connect control panels, safety devices to the motor under the safety regulations in .

Attention: if no stop switch is connected then the terminals 30/31 have to be bridged.

•

The mechanical limits have to be placed so that contact edges are not triggered, as this would lead to an

error message

• Unlock emergency release of operator and set gate to half-opened position. Then lock the operator again

• Then turn on the operator (correct connection necessary).

•

Important:

Putting into operation in Impulse mode (standard setting) and not in dead man mode.

• During initial operation the choice of language and operator (SWING X or SPIN 250) is made first, then in the “Basic

settings” the adjustment of most important operator settings and after the system test, the automatic detection of limit

positions of gate is made.

6. Putting into operation

Swing gate control unit ST 61

LANGUAGE SELECTION

•

Can be selected during initial operation (hence after reset to factory settings).

•

Can be also chosen by pressing the ESC button

(

)

for 5s, from any position in menu.

BASIC SETTING

•

For setting the most important adjustments for initial operation of motor.

•

Can be selected during initial operation (hence when restoring the factory setting).

•

All safety devices are activated when leaving factory

(menu



page 7).

•

The next programming adjustments are made in the main settings menu

(see



6–7).

factory settings

$$$$$$$$$$$$$$$$

impulse button

$$$$$$$$$$$$$$$$

OPEN-STOP-CLOSE

$$$$$$$$$$$$$$$$

OPEN-CLOSE-OPEN

change ? YES

confirm

OPEN

STOP

Select a setting (+/-):



OPEN/STOP/CLOSE



OPEN/CLOSE/OPEN



OPEN



DEADMAN

OPEN

e.g.

return

to previous location

putting into operation

(same step after

factory reset)

5s ESC

(language selection)

$$$$$$$$$$$$$$$$

Sprache-language

Deutsch

confirm

$$$$$$$$$$$$$$$$

Sprache-language

English

scroll

$$$$$$$$$$$$$$$$

basic settings

confirmation

SWING X

SPIN 250

change operator

confirm

$$$$$$$$$$$$$$$$

operator

SWING X

$$$$$$$$$$$$$$$$

operator

SPIN 250

Содержание 12111670

































Результаты поиска

Содержание 12111670

Отзывы:

Бренды по названию

Популярные бренды

tousek 12111670, Руководство по подключению и установке

Результаты поиска

Содержание 12111670

Отзывы:

Бренды по названию

Популярные бренды