Click!
Click!
■
The names of the parts of the paper holder with spare are as follows:
Product Dimensions
■
Make sure that you have the following parts:
*Pay attention to the orientation (top and bottom) of the base
plate when mounting it.
Checking the Accessories
Bearing
Replacing with a spare roll
Taking out and cutting paper
■
Push up the paper cutting plate
and insert a toilet paper roll into
the core rod.
■
In the case of the figure on the right,
when refilling a paper roll to the spare
side, follow the procedure shown below.
Names of Parts
How to Use
Refilling a paper roll
■
Make sure that the product has no backlash after the
installation is complete.
Mounting Method
137
2
3
Core rod
Paper cutting plate
Toilet paper roll
In use
Frame body
Paper
cutting plate
136
30
65
250
300
94
(Flat surface of
the shelf board)
■
Take out the paper from the side having the paper cutting plate,
put your hand on the paper cutting plate to hold it and cut the paper.
■
Install the paper holder as shown in the figure below.
●
Detaching the parts
●
Installation
②
Make prepared holes and fix the base plate securely using
4 supplied mounting screws.
4 pieces
1 unit
1 unit
2 pieces
Use method label
1 piece
Frame body
Base plate
Surface of the shelf of paper holder
670
700
30
65
250
Finished floor surface
*The figure shows YH150RS.
For YH150RS
For YH150RS
In the case of YH150RS
In the case of YH150RS
*The figure shows YH150RS.
(Unit: mm)
(Unit: mm)
A piece of advice
①
Remove the paper
roll in use.
①
Put your hand on the paper
cutting plate to hold it.
②
Cut the paper.
②
Insert a new
paper roll.
③
Insert the removed
paper roll in use again.
①
Lift the paper cutting
plate and take out
the tube of the used
toilet roll.
②
Move the spare
paper roll in the
arrow direction.
③
Lower the paper
cutting plate.
*The figure shows the
view from the back.
Fixing bracket (optional part)
■
When you need a fixing bracket, please place an order for the
following part No. separately.
Resin plug: 20 pieces
T110D28
φ
6 × 30
Part No.
Shape
Details of the set
Preparation for Installation
Mounting Position
■
See the figures below for installation.
70
0
20
70
0
20
YH150RS
YH150LS
130
130
Remove the cushioning material
of the core rod at the end of
installation.
Tip
Tip
Base plate
Pan head tapping screw
(
φ
4.5 x 35): 4 pieces
Use a screwdriver with a bit
length of 100 mm or longer.
Tip
Frame body
④
⑤
⑥
Base plate
Core rod
cushioning material
Bearing
Core rod
cushioning
material
Frame body
(top plate)
Base plate
Base plate
Bearing
Side plate
Frame body
Notch
Notch
Notch
Frame body
(top plate)
Core rod
cushioning
material
Core rod
Base plate
Notch
Binding head screw
(M4 x 6): 2 pieces
⑦
Core rod
cushioning material
Base-plate-mounting
screw
(pan head tapping screw
4.5 x 35)
Frame-body-fixing
screw
(binding head screw
M4 x 6)
When inserting a paper roll into the
core rod, lift the paper roll a little.
You can insert it smoothly by this.
WARNING
■
Use a plywood sheet that is 12 mm or more in thickness on
the mounting surface.
■
When the mounting surface is a thin wall, mount a
reinforcing wooden block that is 30 mm or more in thickness
before installation.
■
When the mounting surface is a concrete base, use
TOTO-designated fixing bracket (optional part).
*Secure a space of 130 mm or more from the open side of the
paper holder to set paper rolls.
WARNING
WARNING
WARNING
①
Remove the tape that holds the frame body and base plate.
②
As shown in the figure, turn the base plate toward you and
remove the bearing from the notch in the frame body.
■
Use the base-plate-mounting screws (pan head tapping
screw
φ
4.5 x 35) that come with the product for
installation.
③
Slide the base plate along the notch in the frame body in the
arrow direction.
①
Mark hole positions in such a way that the product is placed
horizontally.
③
Hold the frame body as shown in the figure so that the top
plate of the frame body faces you, and tilt it in such a way
that the core rod gets in the notch on the back.
④
Fit the notch of the frame body on the core rod, and slide the
frame body along the core rod in the arrow direction.
⑤
In the state where the side plate of the frame body has
passed over the bearing, tilt the frame body as shown in the
figure and turn it to the front.
⑥
Slide the frame body along the bearing toward the wall and
hook the frame body on the base plate.
⑦
Lastly, fix the body to the base plate with screws and
remove the core rod cushioning material.
■
When the mounting surface is a concrete base, use
TOTO-designated fixing bracket (optional part).
Remove the cushioning
material of the core rod at
the end of installation.
