Component parts
Shower bar body
1 set
Elbow pipe
1 part
Fixed shower head (round)
1 part
Wall fixing screws
1 set
Inlet hose (L= 500 )
1 part
Shower hose (L= 1500)
1 part
Hand shower
1 part
Diverter valve
1 set
Product Drawing
Installation and owner manual
To use the product effectively. Should follow the instructions of this manual.
Cuations before installation
1. Hot and cold water pressure during use.
Minimum pressure...................................0.05 MPa (flow pressure)
Maximum pressure..................................0.75 MPa (static Pressure)
2. The hot water temperature should not exceed 65°C. It's recommended in the range of 60±5°C, hot water do not use stream
3. The ambient temperature should above 0°C, if not higher than 0°C, product will be deformed, cracked and other damaged.
4. To prevent internal damage of shower, the water temperature of discharge side should not exceed 60°C. It's recommended
below 45°C.
5. Incase haven't used for long time. It may be lead to internal and external corrosion.
Installation Procedure
Figure 1
Figure 2
Ø
6
Hole Depth 35 mm
Anchor
Holder
Self-tapping screw
(8
5
0
)
Holder
Fastening nut
Taper washer
Retaining wall blocks
Elbow pipe
Fixed
shower
head
Hand shower
Shower hose
Shower hanger
Diverter valve
Holder
Faucet
Water out
connector
Water in
connection
Lever handle
Water out
fittings
Stainless steel
hose (L=500mm)
Warning!
To prevent being scalded due to malfunction, make sure that the diverter valve is switched to the hand shower position in order to
test the water temperature before using. Cannot allow the diverter valve switched underneath over head shower.
Care and Cleaning
Troubleshooting
Check Item
After installation, if there is malfunctions occuring, please see below.
Unstable selection valve
Vibration
Water leak
Problem
Less flow rate
Fastening nut
(1. Have enough tight)
(3. Have enough tight)
(4. Have enough tight)
(7. Have enough tight)
Holder
(2. Have enough tight)
Screw
Hex screw
(5. Have enough tight)
Fastening nut
(6. Have enough tight)
Holder
Screw
(8. Have enough tight)
Hex screw
Your new product is designed for years of trouble-free performance.
1. Keep it looking new by cleaning it periodically with mild soap, rinsing thoroughly with warm water and drying with a clean, soft cloth.
2. Do not use abrasive cleaners, steel wool or harsh chemicals, as these will damage the product.
3. Do not use liquid cleaners with acid-base content. Incase of accidentally happening, rinse with pure water immediately in order to
prevent any damage of product surface.
Failure to follow these instructions may void your warranty.
Warranty
Please find detail in warranty card as attached
Adjusting nut
200mm lift
Hand shower position
Fixed shower position
Figure 3
Figure 4
~
~
Flow Regulator
(10.Dirt)
O-Rings
(11. Scratched)
Gasket rubber
(13. Scratched)
(14. Have enough tight)
Pressure spool
(15. Have enough tight)
(16. Have enough tight)
Lever handle
Fastening screw
Packing
(17. Scratched, dirt)
Packing
(9. Scratched, dirt)
O-rings
(12. Scratched)
10, 17
9, 11, 12, 13, 17
1, 2, 3, 4, 5, 6, 7, 8
14, 15, 16
Require adjust the height of the fixed shower
by adjusting the nut.
1. Installation wall mouting
2. Installation fixed shower head
3. Installation hand shower
4. Trial for tightening confirmatiom
5. Diverter Valve
0-2026-3561
