background image

14

TOSHIBA XM-6201 CD-ROM Drive

Drive Specifications

Specifications and design are subject to change without notice.

Performance

1.

Applicable disk format

Red-book, Yellow-book, CD-ROM XA, 
CD-I Bridge (Photo-CD, Video-CD), 
CD-I, CD-I Ready, CD-G and 
Multisession (Photo-CD, CD-Extra, CD-
RW, CD-R)

2.

Data capacity (Yellow-book)

User data/block

2048 bytes/block (mode 1)

2336 bytes/block (mode 2)

3.

Rotational speed

a

1X (CLV)

6-10X (PCAV)

13.8-32X (CAV)

Approx. 200 to 530 rpm

Approx. 2,000 to 3,000 rpm

Approx. 6,900 rpm

4.

Transfer rate

Sustained block transfer rate

Sustained data transfer rate (mode 1)

Sustained data transfer rate (mode 2)

Burst (SCSI-2 interface)

75 blocks/s (1X)
Approx. 450-750 blocks/s (6-10X)
Approx. 1,035-2,400 blocks/s (13.8-32X)

150 Kbytes/s (1X)
Approx. 900-1,500 Kbytes/s (6-10X)
Approx. 2,070-4,800 Kbytes/s (13.8-32X)

171 Kbytes/s (1X)
Approx. 1,026-1,710 Kbytes/s (6-10X)
Approx. 2,359-5,472 Kbytes/s (13.8-32X)

5 Mbytes/s (async), 10 Mbytes/s (sync)

5.

Access time

Average random access time

b

Average random seek time

c

Average full stroke access time

d

90 ms Typ. (32X)

85 ms Typ. (32X)

140 ms Typ. (32X)

6.

Data buffer capacity

256 Kbytes

7.

Disk loading

Auto front loading (open tray)

8.

Air flow

Not required

9.

Acoustic noise

45 dB (IEC 179 A) max at 1 metre

10. Power supply

+5V DC, +12V DC

Содержание XM-6201B



















Отзывы: