- 16 -
Model
H size
H span
46WIDE 1018.4
485.0
404.1
242.5
80.8
0.0
80.8
242.5
404.1
485.0
80.8
51WIDE 1129.0
537.6
448.0
268.8
89.6
0.0
89.6
268.8
448.0
537.6
89.6
57WIDE 1260.0
600.0
500.0
300.0
100.0
0.0 100.0
300.0
500.0
600.0
100.0
Model
46WIDE 51WIDE 57WIDE
V size
572.850 635.085 708.750
278.4
308.0
344.0
208.8
231.0
258.0
104.4
115.5
129.0
0.0
0.0
0.0
104.4
115.5
129.0
208.8
231.0
258.0
278.4
308.0
344.0
V span
34.8
38.5
43.0
Net Pattern Geometry
CONVERGENCE (46 / 51 / 57 WIDE)
UNIT: mm
ITEM NAME SETTING
INPUT
SIGNAL
TEST POIN
MEASURING
IN STRUMENT
ADJUSTMENT METHOD
ADJUSTMENT SPEC
VCEN VERTICAL
Raster
centeing
Adjustment
CONTRAST :MAX
BRIGHTNESS:CNT
COLOR
:CNT
TINT
:CNT
Retma
Signal
Between TP-G
to TP-V
Digital Volt
Meter
Adjust the volt age between TP-G and TP-V.
0+
-10 mV
DY Tilt
Adjustment
CONTRAST: MAX
BRIGHTNESS:CNT
COLOR :CNT
TINT
:CNT
PIC SIZE
:FULL
D-Cross
Pattern
Picture
Adjustment
Picture
Adjustment
The dummy screen cross
and D-cross Gap +
- 5mm.
Color gap at the screen
center is
- 3mm.
11 +
- 1 bar
In case of C-MUTE OFF is
the same spec as well.
In case of Convergence mute.
Upper left...5 +
- 0.5 bar
Bottom right...5 +
- 0.5 bar
In case of C-MUTE OFF.
Upper left...4 +
- 0.5 bar
Bottom right...4 +
- 0.5bar.
Centering
magnet
Adjustment
CONTRAST: MAX
BRIGHTNESS:CNT
COLOR :CNT
TINT
:CNT
PIC SIZE
:FULL
Retma
Signal
Picture
Adjustment
Picture
Adjustment
WID Horizontal
Adjustment
(FULL)
CONTRAST :MAX
BRIGHTNESS:CNT
COLOR
:CNT
TINT
:CNT
PIC SIZE
: FULL
C-MUTE
:ON
Retma
Signal
Picture
Adjustment
Picture
Adjustment
HIT
(VLI N)
Vertical
Adjustment
(FULL)
CONTRAST :MAX
BRIGHTNESS: CNT
COLOR
:CNT
TINT
:CNT
PIC SIZE
: FULL
C-MUTE
: ON
Retma
Signal
Picture
Adjustment
Picture
Adjustment
Convergence
Retma
Signal
Picture
Adjustment
Picture
Adjustment
Refer to the following (Convergence Net
Geometry)
After roughly the green centering magnet
alignment, adjust the green yoke so that
the D-cross is as close as possible to the
dummy screen cross. Adjust the Red and
Blue in the same manner as Green.
Adjust the green center to the screen
center with the centering magnet on Re-
tma signal. And adjust the Red and Blue
center to the green center each.
Adjust the Horizontal width by WID on
the green raster only.
After finishing Convergence adjustment,
make sure that the width is the same as
the spec.
Adjust the Vertical height by HIT(VLIN)
on the green raster only.After finishing
Convergence adjustment, make sure that
the height is the same as the spec with
C-MUTE OFF.
DEFRECTION and CONVERGENCE
