Toshiba TDP-P9 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 48

background image

TDP-P9

26

(2) Operation test

Buttons operation

Button description

Test criteria

Power button

1. Mechanical motion (Up & Down) should be free from getting stuck

when pressing the button

2. Press “power” button and projector will switch on

Menu/Enter

1. Mechanical motion (Up & Down) should be free from getting stuck

when pressing the button.

2. Press Menu/Enter button can make projector function normally.

4-way button

(Keystone/Auto/Source)

1. Mechanical motion (Up & Down) should be free from getting stuck

when pressing the 4-way button.

2. Press Menu/Enter button can make projector function normally.

Foot adjuster operation

Foot adjuster.

Test criteria

Foot adjuster button

Foot adjusters should stretch downward smoothly by pressing the foot

adjuster buttons on the two sides

Zoom ring and Focus ring

Ring

Test criteria

Zoom ring

Mechanical motion of rotating Zoom ring to the end of right and left by

hand should be free from getting stuck.

Focus ring

The feeling of rotating Focus ring to the end of right and left by hand

should free from seizing

«
...
29
30
31
32
33
...
»

Содержание TDP-P9

















































Отзывы:

Нет отзывов

Похожие инструкции для TDP-P9

Бренд: Vaisala Страницы: 2

Бренд: BenQ Страницы: 124

MP771 - XGA DLP Projector

Бренд: BenQ Страницы: 2

Elite Tripod Series

Бренд: Elite Screens Страницы: 6

Бренд: SVS Страницы: 16

Бренд: Hitachi Страницы: 40

Бренд: HP Страницы: 9

Бренд: HP Страницы: 6

Бренд: HP Страницы: 4

mp3135 - Digital Projector

Бренд: HP Страницы: 4

Бренд: HP Страницы: 4

Бренд: HP Страницы: 4

Бренд: HP Страницы: 4

Бренд: HP Страницы: 1

xp7010 - Digital Projector

Бренд: HP Страницы: 2

Бренд: HP Страницы: 4

Бренд: HP Страницы: 4

Бренд: HP Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды