33
Operations
32
■
Displaying Information [Status display]
This displays information about the input signal, lamp use time, etc.
Press the
button twice.
When the
button is pressed once, the
Setting display menu
appears. Pressing
it again displays information
. The table below shows what kind of information
is displayed. Press the button again to dismiss the display.
“Yes”: displayed, “No”: not displayed
Item
Description
Computer Y/P
B
/P
R
Video
PC Card Camera
S-video
Input
Input source name
Yes
Yes
Yes
Yes
Yes
RGB signal mode RGB input mode
[Note 1]
Yes
No
No
No
No
H-resolution
Horizontal resolution (in bits)
Yes
No
No
No
No
V-resolution
Vertical resolution (in bits)
Yes
No
No
No
No
H-frequency
Horizontal sync frequency
Yes
No
No
No
No
V-frequency
Vertical sync frequency
[Note 2]
Yes
No
No
No
No
Sync
Sync signal polarity
[Note 3]
Yes
No
No
No
No
Signal format
Y/P
B
/P
R
signal format
No
Yes
No
No
No
Video mode
Color method of video signal
No
No
Yes
No
No
Card type
PC card type
No
No
No
Yes
No
Shutter speed
Shutter speed of document
No
No
No
No
Yes
imaging camera
Lamp time
Time of lamp use
[Note 4]
Yes
Yes
Yes
Yes
Yes
Version
Firmware version
[Note 5]
Yes
Yes
Yes
Yes
Yes
MAC address See page 59
No
No
No
Yes
[Note 6]
No
SSID
See page 60
No
No
No
Yes
[Note 6]
No
DHCP
See page 60
No
No
No
Yes
[Note 6]
No
IP address
See page 60
No
No
No
Yes
[Note 6]
No
Subnet mask
See page 60
No
No
No
Yes
[Note 6]
No
Gateway
See page 60
No
No
No
Yes
[Note 6]
No
Notes
1: The mode of supported RGB signals
is shown.
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [
Lamp time
] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the time displayed approaches 2,000
hours, consult with a store about getting a TLPLW1 replacement lamp (sold separately)
prepared.
5: [
Version
] shows the version of the projector’s internal control program. This version is
referred to for customer service, etc.
6: Displayed when wireless LAN PC card is being used.
Notes
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
• Conducting another operation while information is being displayed dismisses the
display.
Using handy features (Continued)
Using the wireless LAN PC card
Please read this chapter if the model you purchased includes a PC card slot.
■
Functions
The following functions are available via wireless communications, when the wireless
LAN PC card and dedicated
Wireless Utility software
included with this projector
are used.
Note: Toshiba does not guarantee operation if a wireless LAN PC card other than
the one supplied with this product is used.
1) Displaying a computer’s screen via the projector
The computer’s desktop screen can be sent, as well as the screens of a variety of
software applications, to the projector for display.
2) Displaying an image saved on a computer via the projector
JPEG files can be sent to the projector for display.
3) Sending images taken with the projector’s document camera to a computer
This function is for models equipped with document camera.
See “Sending the camera’s images to a computer”
for details.
4) Operating the projector by means of a computer
Some of the same functions available from the remote control can be performed.
■
Communication mode
This projector supports both Ad-hoc and Infrastructure Communication modes.
Ad-Hoc Communication Mode
This is transmission mode to communicate
between wireless LAN equipment.
Wireless communication can be performed via
the simple configurations.
This function can only be used if the projector is
in range of the computer’s wireless signals.
For security reason, confirm the specifications of your computer for the distance that
the radio wave can reach. The coverage of this projector may vary, depending on the
computer and the surrounding environment. When tested with a PC manufactured by
Toshiba with built-in wireless LAN system, the coverage is approximately 60 m.
This figure is not guaranteed and should be considered as merely a guideline.
Infrastructure Communication Mode
A mixed wireless and wired LAN can be created
via access points. Connecting to the rest of the
world via a wired LAN or the Internet generally
requires a high level of security.
Use the appropriate transmission mode for your network environment. The instructions
in this owner’s manual assume that you will be using a simple ad-hoc communication
mode setup.
Access point
To LAN,
Internet, etc.
Hub
ON
/S
T A
ND
BY
IN
PU
T
ME
NU
AU
TO
SE
T
F A
N
TE
MP
LA
MP
ON
VO
L.+
VO
L.-
AU
TO
KE
YS
TO
NE
ON
/S
T A
ND
BY
IN
PU
T
ME
NU
AU
TO
SE
T
F A
N
TE
MP
LA
MP
ON
VO
L.+
VO
L.-
AU
TO
KE
YS
TO
NE
