Toshiba Strata CIX40 Скачать руководство пользователя страница 39

Страница: 39 / 208

The Basics

Making a Call

Strata CIX IP5000-series Telephone UG 07/09

Making a Call

There are three ways to originate a call from the telephone:

Handset

1. To make a call, lift the handset, then dial the number.

A line may be automatically selected or choose a line manually. Dial tone is heard
through the handset. The Speaker and Microphone LEDs do

not

light.

Digits display as they are dialed. Call progress tones (Ringback Tone, Busy Tone,
etc.) are heard through the handset.

2. When connected, continue using the handset or switch to speakerphone by holding

down

Spkr

and placing the handset in the cradle.

Spkr Button

1. To make a call, press

Spkr

A line may be selected automatically or choose a line manually. The extension or

Line

button lights (depending on system programming). Dial tone is heard

through the speaker. The Speaker and Microphone LEDs light.

2. Dial the number.

Digits display as they are dialed. Call progress tones (Ringback Tone, Busy Tone,
etc.) are heard through the speaker.

3. When connected, continue using the speakerphone or lift the handset to continue

the conversation.

Hot Dialing

1. To make a call using Hot Dialing, start dialing the number.

The extension button, Spkr and Mic LEDs light. Digits display as they are dialed.
Call progress tones (Ringback Tone, Busy Tone, etc.) are heard through the
speaker.

2. When connected, continue using the speakerphone or lift the handset to continue

the conversation.

Содержание Strata CIX40

















































































































































































































Результаты поиска

Содержание Strata CIX40

Отзывы:

Похожие инструкции для Strata CIX40

Бренды по названию

Популярные бренды

Toshiba Strata CIX40, Руководство пользователя

Результаты поиска

Содержание Strata CIX40

Отзывы:

Похожие инструкции для Strata CIX40

Бренды по названию

Популярные бренды