manualshive.com logo in svg

Toshiba SD-V320SCA, Руководство по обслуживанию

Поделиться
Скачать
Toshiba SD-V320SCA Скачать руководство пользователя страница 35

DISASSEMBLY INSTRUCTIONS

B1-1

1. REMOVAL OF MECHANICAL PARTS

AND P.C. BOARDS

1.

2.

Open Flap to 90˚ and flex in direction of arrow (A), at the
same time slide in direction of arrow (B).
Then lift in direction of arrow (C).

1-3: DVD DECK/DVD PCB (Refer to Fig. 1-3)

1-2: FLAP (Refer to Fig. 1-2)

Fig. 1-2

(A)

Flap

(B)

(C)

Fig. 1-3

1.

2.

3.
4.
5.

6.
7.
8.

9.
10.
11.

Make the short circuit on the position as shown Fig. 1-3
using a soldering. If you remove the DVD Deck with no
soldering, the Laser may be damaged.
Unlock the support 

1

 and remove the Deck Top Holder

in the direction of arrow (A).
Remove the 2 screws 

2

.

Remove the 2 screws 

3

.

Disconnect the following connectors:
(CP501, CP8001).
Remove the DVD Deck in the direction of arrow (B).
Remove the 2 screws 

4

.

Disconnect the following connectors:
(CP2601, CP2602, CP2603).
Remove the DVD PCB in the direction of arrow (C).
Remove the 3 screws 

5

.

Remove the Front Angle in the direction of arrow (D).

NOTE

When the installation of the DVD Deck, remove all the
soldering on the short circuit position after the connection of
Pick Up PCB and VCR PCB connector.

2

1

Deck Top Holder

2

3

(A)

3

4

DVD Deck

5

4

(B)

DVD PCB

(C)

5

Front Angle

5

Make the sort circuit
using a soldering.

Pick Up PCB

(D)

1-1: TOP CABINET, FRONT CABINET, OPERATION 1/2

PCB AND FRONT JACK PCB (Refer to Fig. 1-1)

1.
2.
3.

4.
5.
6.
7.

8.

Remove the 5 screws 

1

.

Remove the Top Cabinet in the direction of arrow (A).
Disconnect the following connectors:
(CP651 and CP652).
Unlock the 8 supports 

2

.

Remove the Front Cabinet in the direction of arrow (B).
Remove the 11 screws 

3

.

Remove the Operation 1/2 PCB and Front Jack PCB in
the direction of arrow (C).
Remove the 3 Pin Shield.

Fig. 1-1

1

1

2

Top Cabinet

1

1

1

(A)

2

2

2

2

2

(B)

2

(C)

3

Operation 1 PCB

3 Pin Shield

Front Jack PCB

3

3

3

3

3

3

33

3

3

2

Front Cabinet

Operation 2 PCB

Содержание SD-V320SCA
























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды