Toshiba Satellite ProT130D Скачать руководство пользователя страница 171

Страница: 171 / 274

Chapter 4 Replacement Procedures

Satellite T130D, Satellite Pro T130D , and PORTEGE T130D Maintenance Manual (960-Q08)

4.5 Keyboard

Removing the keyboard

The following describes the procedure for removing the keyboard (See Figure 4-5-1 to 4-5-2).

CAUTION:

As the keycap may fall out, when handling the keyboard always hold it by the

frame and do not touch the keycap.

Upside down the computer and remove the battery.

Loose the screws on KB holder.

M2.0x2.0B Flat BIND screws

Open the display.

Insert your finger into the slot between the KB holder and the keyboard. Then, lift up

the

keyboard holder

to remove it.

Loose the

screw

securing Keyboard.

M2.0x3.0B Flat BIND screws

Insert your finger into the slot between keyboard and Top cover Assembly. Then lift

up the

keyboard

to remove it.

Disconnect keyboard cable.

Содержание Satellite ProT130D



















































































































































































































































































Результаты поиска

Содержание Satellite ProT130D

Отзывы:

Похожие инструкции для Satellite ProT130D

Бренды по названию

Популярные бренды

Toshiba Satellite ProT130D, Руководство по обслуживанию

Результаты поиска

Содержание Satellite ProT130D

Отзывы:

Похожие инструкции для Satellite ProT130D

Бренды по названию

Популярные бренды