manualshive.com logo in svg

Toshiba Satellite M300, Руководство по обслуживанию, Страница: 67 / 308

Поделиться
Скачать
Toshiba Satellite M300 Скачать руководство пользователя страница 67

2 Troubleshooting Procedures  

 

Satellite M300 and Satellite Pro M300 Maintenance Manual (960-Q08)                 

 23 

Procedure 2 

Diagnostic Test Program Execution Check 

Insert the Diagnostics Disk in the USB FDD, turn on the computer and run the test. Refer to 
Chapter 3, 

Tests and Diagnostics,

 for more information about the diagnostics test procedures. 

Make sure the floppy disk is formatted correctly and that the write protect tab is disabled. 
Floppy disk drive test error codes and their status names are listed in Table 2-7. If any other 
errors occur while executing the FDD diagnostics test, go to Check 1. 

Table 2-7    FDD error code and status 

Code Status 

01h Bad 

command 

02h 

Address mark not found 

03h Write 

protected 

04h 

Record not found 

06h Media 

replaced 

08h 

DMA overrun error 

09h 

DMA boundary error 

10h CRC 

error 

20h FDC 

error 

40h Seek 

error 

60h 

FDD not drive 

80h 

Time out error (Not ready) 

EEh 

Write buffer error 

FFh 

Data compare error 

 

Check 1 

If the following message is displayed, disable the write protect tab on the floppy 
disk by sliding the write protect tab to “write enable”. If any other message 
appears, perform Check 2. 

Write protected

 

Check 2 

Make sure the floppy disk is formatted correctly. If it is, go to Procedure 3. 

Содержание Satellite M300





















































































































































































































































































































Отзывы:

Нет отзывов