manualshive.com logo in svg

Toshiba Satellite E200, Руководство по обслуживанию


Поделиться
Скачать
background image

 

 

Satellite/E200/E205     Maintenance Manual 

 

iii 

Preface 

This maintenance manual describes how to perform hardware service maintenance for the 
Toshiba Personal Computer Satellite E200/E205, referred to as Satellite E200/E205 in this 
manual. 

The procedures described in this manual are intended to help service technicians isolate 
faulty Field Replaceable Units (FRUs) and replace them in the field. 

SAFETY PRECAUTIONS 

Four types of messages are used in this manual to bring important information to your 
attention.  Each of these messages will be italicized and identified as shown below. 

DANGER: “Danger” indicates the existence of a hazard that could result in death or 
serious bodily injury, if the safety instruction is not observed. 

 

WARNING: “Warning” indicates the existence of a hazard that could result in bodily 
injury, if the safety instruction is not observed. 

 

CAUTION: “Caution” indicates the existence of a hazard that could result in property 
damage, if the safety instruction is not observed. 

 

NOTE: “Note” contains general information that relates to your safe maintenance 
service. 

 

Improper repair of the computer may result in safety hazards. Toshiba requires service 
technicians and authorized dealers or service providers to ensure the following safety 
precautions are adhered to strictly. 

 

Be sure to fasten screws securely with the right screwdriver. If a screw is not fully 
fastened, it could come loose, creating a danger of a short circuit, which could cause 
overheating, smoke or fire. 

 

If you replace the battery pack, RTC battery or backup battery, be sure to use only the 
same model battery or an equivalent battery recommended by Toshiba. Installation of 
the wrong battery can cause the battery to explode. 

Содержание Satellite E200




















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Satellite E200

Panasonic The Toughbook 31 Features preview
The Toughbook 31
Бренд: Panasonic Страницы: 2
Gateway MT6840 Setup preview
MT6840
Бренд: Gateway Страницы: 2
EUROCOM racer 4w User Manual preview
racer 4w
Бренд: EUROCOM Страницы: 346
Core Innovations CLT136401 User Manual preview
CLT136401
Бренд: Core Innovations Страницы: 26
ANSMANN FLEX LIGHT Instruction Manual preview
FLEX LIGHT
Бренд: ANSMANN Страницы: 10
Acer Chromebook 14 for Work User Manual preview
Chromebook 14 for Work
Бренд: Acer Страницы: 32
Acer CN315-71P User Manual preview
CN315-71P
Бренд: Acer Страницы: 86
Acer ConceptD 5 User Manual preview
ConceptD 5
Бренд: Acer Страницы: 79
Acer ConceptD 9 User Manual preview
ConceptD 9
Бренд: Acer Страницы: 81
Acer E525 Guía Rápida preview
E525
Бренд: Acer Страницы: 13
NEC Versa E3100 Disassembly Manual preview
Versa E3100
Бренд: NEC Страницы: 25
NEC Versa M540/PB EasYnote R7 Disassembly Manual preview
Versa M540/PB EasYnote R7
Бренд: NEC Страницы: 25
NEC VERSA M350 Disassembly Manual preview
VERSA M350
Бренд: NEC Страницы: 30
NEC VERSA N1200 Series User Manual preview
VERSA N1200 Series
Бренд: NEC Страницы: 75
NEC Versa 2730M User Manual preview
Versa 2730M
Бренд: NEC Страницы: 116
NEC Versa AX Disassembly Manual preview
Versa AX
Бренд: NEC Страницы: 18
NEC VERSA 500D WINDOWS 98 - UPGRADE INFORMATION Manual preview
VERSA 500D WINDOWS 98 - UPGRADE INFORMATION
Бренд: NEC Страницы: 5
NEC Versa 2500 Series Service Manual preview
Versa 2500 Series
Бренд: NEC Страницы: 104

Бренды по названию

Популярные бренды

Загрузить еще бренды