Toshiba RAS-24SKV Series, Руководство пользователя

Страница: 3 / 8

Toshiba 1110650156 (EN)
1. Press
MODE
: Select Cool , Heat or Fan only .
2. Press
TEMP
: Set the desired temperature.
Cooling: Min. 17°C, Heating: Max. 30°C, Fan Only: No temperature
indication
3. Press
FAN
: Select AUTO, LOW , LOW+ , MED ,
MED+ , or HIGH .
For dehumidification, a moderate cooling performance is controlled
automatically.
1. Press
MODE
: Select Dry .
2. Press
TEMP
: Set the desired temperature.
To automatically control room temperature and airflow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
Press
Hi-POWER
: Start and stop the operation.
In case of the misplaced or discharged remote control
• Pressing the RESET button, the unit can start or
stop without using the remote control.
• Operation mode is set on AUTOMATIC operation,
preset temperature is 25°C and fan operation is
automatic speed.
Set the timer when the air conditioner is operating.
Daily timer allows the user to set both the ON & OFF timers and will be
activated on a daily basis.
Setting Everyday Timer
• During the every day timer is activating, both arrows ( , ) are indicated.
Note:
• Keep the remote control in accessible transmission to the indoor unit;
otherwise, the time lag of up to 15 minutes will occur.
• The setting will be saved for the next same operation.
To automatically control room to save energy (except in DRY and FAN ONLY mode)
Press
ECO
: Start and stop the operation.
Note: Cooling operation; the set temperature will increase automatically 1
degree/hour for 2 hours (maximum 2 degrees increase). For heating
operation the set temperature will decrease.
COOLING / HEATING / FAN ONLY OPERATION
7
DRY OPERATION
8
Hi-POWER OPERATION
9
ECO OPERATION
10
TEMPORARY OPERATION
11
TIMER OPERATION
12
1
Press
FIX
: Move the louver in the
desired vertical direction.
2
Press
SWING
: Swing the air
automatically and press again to stop.
3
For horizontal direction, adjust
manually.
Preparing Filters
1. Open the air inlet grille and remove the air filters.
2. Attach the filters. (see detail in the accessory sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new batteries (AAA type) following the (+) and
(–) positions.
Clock Setup
1. Push CLOCK • by tip of the pencil.
If timer indication is flashing, go to the next step 2.
2. Press ON or
OFF
: adjust the time.
3. Press
SET
: Set the time.
Remote Control Reset
1. Remove the batteries.
2. Press
.
3. Insert the batteries.
1
Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5
Fan speed button (FAN)
6
Swing louver button (SWING)
7
Set louver button (FIX)
8 On timer button (ON)
9 Off timer button (OFF)
!
Sleep timer button (SLEEP)
"
Setup button (SET)
#
Clear button (CLR)
$ Memory and Preset button (PRESET)
% One-Touch button (ONE-TOUCH)
& High power button (Hi-POWER)
(
Economy button (ECO)
)
Quiet button (QUIET)
~
Comfort sleep button (COMFORT SLEEP)
+ Filter reset button (FILTER)
, Clock Reset button (CLOCK)
-
Check button (CHK)
Press the “ONE-TOUCH” button for fully automated operation that is customized
to the typical consumer preferences in your region of the world. The customized
settings control temperature air flow strength, air flow direction and other settings
to provide you alternate contact with “ONE-TOUCH” of the button. If you prefer
other settings you can select from the many other operating functions of your
Toshiba unit.
Press
ONE-TOUCH
: Start the operation.
To automatically select cooling or fan only operation
1. Press
MODE
: Select A.
2. Press
TEMP
: Set the desired temperature.
3. Press
FAN
: Select AUTO, LOW , LOW+ , MED ,
MED+ , or HIGH .
PRESET
ONE-TOUCH
QUIET
SWING
TIMER
ON
FILTER CHK CLOCK
OFF
CLR
SLEEP SET
FIX Hi-POWER ECO
COMFORT
SLEEP
MODE
TEMP
FAN
PREPARATION BEFORE USE
2
AIR FLOW DIRECTION
3
REMOTE CONTROL
4
ONE-TOUCH
5
AUTOMATIC OPERATION
6
Setting the ON Timer Setting the OFF Timer
1
Press ON
Press
OFF
: Set the desired OFF timer.
2
Press
SET
: Set the timer. Press
SET
: Set the timer.
3 Press
CLR
: Cancel the timer. Press
CLR
: Cancel the timer.
1
Press
ON
: Set the ON timer.
3
Press
SET
.
2 Press
OFF
: Set the OFF timer. 4
Press
SET
: button during
the ( or ) mark flashing.
Note:
• Do not move the louver manually by others.
• The louver may automation positioning by some operation mode.
: Set the desired
ON timer.
1110650156_pf1.indd 3 02/21/11 10:11 AM