manualshive.com logo in svg

Toshiba RAS-24N3AV2-A, Руководство по обслуживанию

Поделиться
Скачать
Toshiba RAS-24N3AV2-A Скачать руководство пользователя страница 57

– 

56

 –

When the installation plate is directly
mounted on the wall

1. Securely fit the installation plate onto the wall by

screw

ing it in the 

upper and lower 

parts to 

h

ook up the indoor unit.

2. To mount the installation plate on a concrete wall

with anchor bolts, use the anchor bolt holes as

illustrated in the below figure.

3. Install the installation plate horizontally 

in the wall

.

CAUTION

When installing the installation plate with mounting
screw, do not use the anchor bolt hole

s

.

Otherwise

,

 the unit may fall down and result in

personal injury and property damage.

Fig. 10-3-4

Fig. 10-3-5

CAUTION

Failure to securely install the unit may result in
personal injury and property damage if the
unit falls.

• In case of block, brick, concrete or similar type

walls, 

make

 5 mm dia. holes in the wall.

• Insert clip anchors for 

appropriate mounting 

Anchor bolt

Projection 
15 mm or less

5 mm dia. hole

Clip anchor
(local parts)

 7  Mounting screw
     Ø4 × 25 

l

10-3-

3

. Wiring Connection

How to connect the connecting cable

Wiring 

of 

the connecting cable can be carried

out without removing the front panel.

1. Remove the air inlet grille. Open the air inlet

grille upward and pull it toward you.

2. Remove the terminal cover and cord clamp.

3. Insert the connecting cable (or as according to

local r

ule

) into the pipe hole on the

wall.

4. 

Take out

 the connecting cable through the cable

slot 

on the rear panel so that it protrudes about

15 cm 

from

 the front.

5. Insert the connecting cable fully into the terminal

block and secure it tightly with screws.

6. T

ighten firmly but not over :

 1.2 N•m (0.12 kgf•m)

7. Secure the connecting cable with the cord clamp.

8. 

Fix

 the terminal cover, rear plate bushing and

air inlet grille on the indoor unit.

FILE NO. SVM-13004

screws  7  .

NOTE :

• 

Secure four corners and lower parts 

the installation plate 

with

 4 to 6

 mounting screws to install it.

CAUTION

•

  

Be sure to refer to the wiring system diagram

labeled inside the front panel.

•

  

Check local electrical cords and also any specific

wiring instructions or limitations.

CAUTION

1

2

3

Cord clamp

Terminal block

Terminal cover

Screw

Earth line

Screw

Connecting cable

Earth line

110mm

20mm

80mm

10mm

Connecting 
cable

Stripping length of the connecting cable

About 15 cm

Fig. 10-3-6

NOTE :

• 

Use stranded wire only.

•

  Wire type : More than 1.5 mm  (H07RN-F or 60245

IEC66) or 1.3 mm  (AWG-16)

2

2

Installation plate
(Keep horizontal direction)

Содержание RAS-24N3AV2-A


































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды