Toshiba RAS-107SAV-E Скачать руководство пользователя страница 38

Страница: 38 / 86

−

Item

Operation flow and applicable data, etc.

Description

FILE NO. SVM-10017

14. Hi-POWER ([Hi-POWER] button on the remote controller

is pressed)

When [Hi-POWER] button is pressed while the indoor
unit is in Auto, Cooling or Heating operation, Hi-

Mode

POWER mark is indicated on the display of the remote

controller and the unit operates as follows.

1. Automatic operation

•

The indoor unit operates in according to the

current operation.

2. Cooling operation

remote controller does not change.)
The indoor unit's fan speed level increase 1 tap

•

The preset temperature drops 1ºC

(The value of the preset temperature on the

3. Heating operation

remote controller does not change.)
The indoor unit's fan speed level increase 1 tap

•

The preset temperature increases 2ºC

(The value of the preset temperature on the

4. The Hi-POWER mode can not be set in Dry

operation

. COMFORT

The principles of comfort sleep mode are:

•

Quietness for more comfortable. When

•

Save energy by changing room temperature

•

The air condition can shut down by itself

Remarks:

Comfort sleep mode will not operate in dry

automatically.

mode and fan only mode.

automatically.

room temperature reach setting temperature

•

The preset temperature will increase as
show on ECO operation (Item No. 9)

•

Press the [COMFORT SLEEP] button to

choose the operating hours. Repeat

pressing to select the hours.

•

If the [COMFORT SLEEP] button is pressed
again means cancel comfort sleep mode.

Heating mode

•

The preset temperature will drop down as
show on ECO operation (Item No. 9)

choose the operating hours. Repeat

•

Press the [COMFORT SLEEP] button to

pressing to setect thehours.

•

If the [COMFORT SLEEP] button is pressed
again means cancel comfort sleep mode.

(1hr, 3hr, 5hr or 9hr)

(1hr, 3hr, 5hr or 9 hr)

SLEEP

Cooling mode

Содержание RAS-107SAV-E























































































Результаты поиска

Содержание RAS-107SAV-E

Отзывы:

Похожие инструкции для RAS-107SAV-E

Бренды по названию

Популярные бренды

Toshiba RAS-107SAV-E, Руководство по обслуживанию

Результаты поиска

Содержание RAS-107SAV-E

Отзывы:

Похожие инструкции для RAS-107SAV-E

Бренды по названию

Популярные бренды