Toshiba PDR-M500 Скачать руководство пользователя страница 48

Страница: 48 / 49

Section

8. Specifications

Model name

PDR-M500

Sensor

1/2.7” CCD sensor

(total pixel count: Approx. 2.14 million)

Sensitivity

Manual setting: Equivalent to ISO 70/100/200/400

Automatic setting: Equivalent to ISO70/100/200/400/70 to 200/70 to 400

Lens

10X optical zoom lens F2.8 - F3.1

Focal distance

f=5.7 mm - 57 mm (equivalent to 37 mm - 370 mm on a 35 mm camera)

Finder

Electronic View Finder

Auto-focus

TTL system. AF, focus adjusting range: approxi. 10 cm to infinity (Wide side setting)

Detection system: Contrast detection system (frame rate during detection: 30 Hz)

Photometry mode

Center Priority Photometry, Spot Photometry

Exposure control system

Program AE, Aperture-priority, Shutter-priorrity, Manual

Exposure compensation

-2.0 EV to +2.0 EV (in 1/3 EV increments)

Aperture

F2.8 to F8 automatic selection, manual selection possible

Shutter speed

1/2 to 1/2000 sec. (electronic shutter and mechanical shutter)

Maximum 16 sec. For extended exposure photography

White balance

Auto/manual setting selectable (7 modes)

Focal range

Standard: Approx. 50 cm to infinity (Wide side setting),

approx. 1.2 m to infinity (Tele side setting)

Macro: Approx. 10 cm to infinity (Wide side setting),

approx. 90 cm to infinity (Tele side setting)

Self-Timer

Time selectable between 2 seconds/10 seconds selectable

Flash settings

Auto firing mode (automatic in low-brightness conditions)/

Red-eye Reduction/Forced Flash/Suppressed Flash/Slow Sync

Focal range: Approx. 0.5 m to 4.4 m (Tele side setting, ISO 400)

Date/time

Simultaneously Recorded to image data (Exif file format)

Automatic calendar function

Automatically adjusted until the year 2099

LCD monitor

2.5” low-temperature polysilicon TFT (117,600 pixels)

Interface

DC IN 5V terminal: 5 VDC
DIGITAL terminal: USB (Ver. 1.1, Mass storage class compatible)

AV terminal: Supplied AV cable compatible

MIC (external microphone IN) terminal (compatible mike:
Diameter: 3.5 mini-plug, monophonic, output impedance 1.8 ohm

Power

4 × AA (Alkaline, Ni-MH or Lithium) batteries Two CR-V3

Lithium Battery Packs or AC adapter (PDR-AC20) (sold separately)

Recording medium

Supports SD memory cards 8/16/32/64/128/256/512 MB

Compressed format

JPEG compliant

Image file format

Exif Ver. 2.2 compliant

Compatibility rules

DCF Ver. 1.0 compliant

Operating environment

Temperature: +32 °F ( ±0°C) to +104 °F (+40 °C) (during operation)/-4°F (-20°C) to

+140 °F (+60 °C) (during storage)

Humidity: 30% to 80% (during operation) no condensation

Dimensions

109.6 mm × 76.8 mm × 66.0 mm (W × H × D) excluding protrusions

Weight

Approx. 300g (excluding accessories, batteries, SD card)

Содержание PDR-M500


















































Результаты поиска

Содержание PDR-M500

Отзывы:

Похожие инструкции для PDR-M500

Бренды по названию

Популярные бренды

Toshiba PDR-M500, Руководство по обслуживанию

Результаты поиска

Содержание PDR-M500

Отзывы:

Похожие инструкции для PDR-M500

Бренды по названию

Популярные бренды