Toshiba P42LSA+ Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 46

Toshiba P42LSA+ Скачать руководство пользователя страница 15

15

SELECTION of the SIGNALS

Video input

VIDEO-1            Composite Video signal,                  US-Pin (RCA)        NTSC/PAL
VIDEO-2            Y/C    (S-VIDEO)                                S connector            NTSC/PAL
VIDEO-3            Y-Pb-Pr(Y-Cb-Cr)                              YUV mini-DIN      NTSC/PAL/up to 480p

Note: Y-Pb-Pr (Y-Cb-Cr) terminal can accept up to 720p signal. Higher resolution signals are

Supplied through RGB terminal.

RGB input

RGB-1 Analog RGB (PC signal) D-sub HD 15-pin RGB analog signal/Y-Cb-Cr signal
DIGITAL RGB Digital DVI-D input RGB digital signal for PC
(DVI-D signal input is for PC only, HDCP: not compatible)

HD-SDI input

HD-SDI Digital High Definition Bit stream signal BNC connector

FUNCTION OF POWER PANEL

No. Name

Function

Remarks

1 Power Switch

Turn ON and OFF main power ON/OFF

2 AC Inlet AC 100-240V, 50/60Hz input 3P plug

POWER SWITCH AND POWER INDICATOR

AC power source is turned-on/off with the Main Power Switch.

When the Power Switch is turned-on, the Power Lamp Indicator
lights in green and the unit enters active state. It takes several
seconds typically till an image is shown after Power Switch is
turned-on.

In the active state, it is possible to power on/off with an external

controller or remote control. When power is turned-off with an
external controller or remote control, the Power Indicator light will
change to yellow and the Display unit enters standby state.

RS232C-RS485 connection hint

Interval from turn-off to turn-on
should be more than 5 seconds.

Power lamp indicates green at
Power On, No-signal and sleep
are orange, stand-by is Yellow.

«
...
13
14
15
16
17
...
»

Содержание P42LSA+















































Отзывы:

Нет отзывов