manualshive.com logo in svg

Toshiba MR-2018, Руководство по обслуживанию

Поделиться
Скачать
Toshiba MR-2018 Скачать руководство пользователя страница 7

MR-2019/2018/MY-1034  UNPACKING AND INSTALLATION  2 - 1

[2] UNPACKING AND INSTALLATION

1. MR-2018/2019 Installation

The installing procedures below are described for the MR-2018.
The installing procedures for the MR-2019 are the same as below.

Turn the main switch to the “OFF” position and remove the power
plug from the outlet.

1)

Remove the document cover.

Remove the document cover from the copier.

2)

Remove the rear cabinet.

Remove the three screws and then remove the rear cabinet.

3)

Replace the right glass holder (For Europe only).

<1> Remove the two screws, and remove the right exterior

OC.

<2> Attach the right glass holder, and fix it with the two screws

which was removed in the above procedure.

Installation manual: 1 sheet

•

Parts included

Right glass holder: 1 pc.
(For Europe only)

Screw (M3 x 8): 1 pc.

Screw (M3 x 6): 1 pc.

MR-2018 Unit (ADF Unit)

MR-2018 Unit (RADF Unit)

"OFF"

Содержание MR-2018

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды