background image

 

 
 

 

SPECIFICATIONS –MK4019GAX (HDD2171)  

General 

Model MK4019GAX 

(HDD2171) 

Interface ATA-2/3/4/5 
Motor 

Fluid Dynamic Bearing (FDB) 

Functionality

 

Formatted Capacity 

40.0078GB* 

Rotational Speed 

5,400rpm 

Avg. Rotational Latency 

5.55/ms 

Spin-up Time 

4sec (typical) 

Buffer 16MB 
Seek Time (Average)  

12  

Internal Transfer Rate 

200.8 ~ 333.2 Mbits/sec (max) 

Host Transfer Rate  

100Mbytes/sec  

*Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes. 

Internal Drive Characteristics

 

Number of Disks 

Number of Read/Write Heads 

Track Density (TPI) 

57.1k 

User Data Cylinders 

33,440 

Logical Cylinders 

16,383 

Logical Heads 

16 

Logical Sectors/track 

63 

Bytes per Sector 

512 

Logical Blocks (LBA) 

78,140,160 

Reliability 

Preventative maintenance 

None 

Nonrecoverable read errors 

1 error per 10

13

 bits read 

Electrical

  

Voltage 5V 

5% 

Power Consumption

 

Start 5.0W 

typ 

Seek 2.9W 

typ 

Read/Write 2.5W 

typ 

Sleep 0.1W 

typ 

Energy Consumption Efficiency  0.021W/GB avg  

Shock 

Operating 1,960m/s

2

 (200G)(2msec) 

Non-Operating 7,840m/s

2

 (800G)(1msec) 

 

Содержание HDD2171












Отзывы: