background image

 

 
 

 

SPECIFICATIONS – MK1214GAP (HDD2149)  

General 

Model MK1214GAP 

(HDD2149) 

Interface ATA-2/3/4 

Functionality

 

Formatted Capacity 

12.072GB*

Rotational Speed 

4200rpm 

Avg. Rotational Latency 

7.14/ms 

Spin-up Time 

4sec (typical) 

Buffer 1024KB 
Seek Time (Average)  

13 

Internal Transfer Rate 

104.35 ~ 193.88Mbits/sec (max) 

Host Transfer Rate  
        Ultra DMA mode 
         PIO Mode 

 
66.7Mbytes/sec  
16.6Mbytes/sec 

Interleave Factor 

1.1 

*Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes.

 
Internal Drive Characteristics

 

Number of Disks 

Number of Read/Write Heads 

Track Density (TPI) 

1022 (26.0K) 

Logical Cylinders 

16,383 

Logical Heads 

16 

Logical Sectors/track 

63 

Bytes per Sector 

512 

Logical Blocks (LBA) 

23,579,136 

 
Reliability 

Preventative maintenance 

None 

Nonrecoverable read errors 

1 error per 10

13

 bits read 

 
Electrical

  

Voltage 5V 

±5% 

 
Power Consumption

 

Start 2.7W 

typ 

Seek 2.3W 

typ 

Read/Write 2.2W 

typ 

Sleep 0.1W 

typ 

Energy Consumption Efficiency 

0.054W/GB avg  

 
Shock 
Operating 1,470m/s

2

 (150G)(2msec) 

Non-Operating 6,8600m/s

2

 (700G)(1msec) 

Содержание HDD2149












Отзывы: