Toshiba GX9 ASD Скачать руководство пользователя страница 77

Страница: 77 / 100

GX9 ASD Quick Start Guide

Trips/Faults

Trip

is a

GX9 ASD

response to a

Fault

(though

Fault

and

Trip

are sometimes used interchangeably).

Trip

is a safety feature that disables the ASD system in the event that a subsystem of the ASD is

malfunctioning or a parameter setting has been exceeded.

Listed in

Table 8

are the

Faults

that may result in a

Trip

and the possible causes. When a

Trip

is incurred

the system displays the

Fault

screen. The

Fault

screen identifies the active

Fault

Table 8. GX9 ASD Fault Listing.

LED Screen

LCD Screen

Possible Causes/Troubleshooting

AbFL

Virtual Linear Pump
Abnormal Flow

• Loss of suction pressure or closed pump output valve.

• Activated discrete input terminal set to

Low Suction/No Flow Protection

• ASD Upper-Limit Frequency run-time is equal to

F936

time setting.

Emergency Off

• Output signal from the ASD is terminated and a brake may be applied if so

configured.

• Emergency Off command received via EOI or remotely.

E-10

Sink/Source Setting
Error

• Improperly positioned

Sink/Source

jumper on the Terminal board or on an

option device (see J100 at the Terminal Board of the ASD).

•

Sink/Source

configuration is incorrect.

E-11

Brake Sequence
Response Error

•

F630

is set to a non-zero value.

• Braking sequence discrete input and output terminals are not set up properly.

E-12

Encoder Signal-Loss
Error

• ASD is configured to receive a signal from a shaft-mounted encoder and no

signal is being received while running.

• Disconnection at the Encoder circuit.

• Motor is stopped and is generating torque via torque limit control.

• ASD is not configured properly.

E-13

Speed Error

• Result of a motor speed that is greater than the commanded speed when

using an encoder for speed control.

• Improper encoder connection or setup information.

• Defective encoder.

E-17

Key Failure

• Same key input for 20 seconds or more.

E-18

Analog (Terminal)
Input Loss

• VI/II signal loss.

• Terminal Board failure.

• P24 over-current condition.

E-19

CPU Communication
Error

• CPU data Transmit/Receive error.

E-20

V/f Control Error

• Torque processing error.

• Make service call.

E-21

CPU Processing Error

• Software processed incorrectly.

• Make service call.

E-22

Logic Input Voltage
Error

• Incorrect voltage applied to the discrete input terminals.

Содержание GX9 ASD





































































































Результаты поиска

Содержание GX9 ASD

Отзывы:

Бренды по названию

Популярные бренды

Toshiba GX9 ASD, Быстрый старт

Результаты поиска

Содержание GX9 ASD

Отзывы:

Бренды по названию

Популярные бренды