Toshiba GR-WG71MDA, Руководство пользователя

Страница: 6 / 12

储⽔箱和盖⼦
Tank and lid
向上拉出储⽔箱卡板，卸下盖⼦。
Pull the tank stopper upwards and detach the cover.
•
维护后，请将盖⼦上的“挂勾” 挂在⽔箱內部，然后⽤朝着您⾝体⽅向的⽔箱卡板扣紧。
如果盖⼦未完全关闭，则⽆法制作冰块。
•
After maintenance, hang the “hook” of the cover to the inside of the tank and fasten it with the
tank stopper being towards you.
If the cover is not completely closed, the ice cannot be made.
如何拆卸和安装
How to detach and install
1
朝箭头所⽰⽅向转动⽔管并将其从供⽔帽上卸下。
要重新安装，将供⽔管插到供⽔帽的管⼦上。然后按所⽰的反⽅向拧紧⽔管。请勿拆下供
⽔管。（否则可能导致某种程度的损坏）。
Turn the pipe following the arrow direction and remove from the cap.
To re-install, insert the water supply pipe to the pipe of the cap. Then, tighten
it in reverse direction of the arrow as shown. Do not remove the water supply
pipe. (This can cause some damages.)
2
3
按箭头所⽰⽅向旋转松开管帽。
Rotate to release the cap following the arrow direction as shown.
注
Note
HOOK
挂勾
Water supply pipe and pump
供⽔管和⽔泵
•
请勿使⽤漂⽩剂、清洁剂或热⽔（装置的耐热温度为
60°C
）、硬⽑刷、稀释剂、苯等物质。（这些物质会导致臭味和损坏。）
•
Do not use bleach, cleanser, hot water (the heat-resistible temperature of the equipment is 60°C), a scrubbing brush,
thinner, benzene, etc. (Such materials can cause smell and damages.)
•
请勿将洗涤⽔倒⼊进⽔阀安装区域。
否则会损坏制冰机组件。
•
Do not pour out the washed water on the area of water inlet valve installation. (Parts side)
This can damage the ice maker assembly.
•
请仅在维护时拆开部件，且每次都应重新安装到位。如果部件未安装到位，则将有⽔溢出或⽆法制作冰块。
•
Detach the assembly for maintenance only and re-install into place every time. Unless the parts are re-installed, the water will
spill over or the ice cannot be made.
AUTOMATIC ICE MAKER (continued)
⾃动制冰机（续）
The heat-resistible
temperature of all parts
is
60°C.
⽇常维护及⾸次使⽤维护 General and the First Time Use Maintenance
各部位的耐热温度为
60°C
每周维护
Weekly Maintenance
每⽉维护
Monthly Maintenance
Pump
⽔泵
Axle
Edged
Hole
边孔
轮轴
储⽔箱
Tank
Water Supply Cap
Water-fill Port
Tank Lid
water Supply Pipe-A
Pump
Tank
Tank Stopper
储⽔箱盖
供⽔帽
供⽔管
- A
储⽔箱卡板
供⽔⼝
储⽔箱
⽔泵
Water Supply Valve
供⽔管
Cap
盖帽
供⽔阀
如何安装⽔泵
How to install the pump
1
安装⽔泵组件。
2
按箭头所⽰⽅向旋转⽔泵帽。
⽔泵叶轮由磁体制成。磁体将被吸在电动机上。
因此，请却认磁体上未粘有异物
。
Rotate the pump cap following the arrow direction.
⽔泵叶轮
Pump Impeller
4
⽤沾有清⽔的海棉轻轻擦拭供⽔管 、⽔泵叶轮、⽔泵盒、⽔泵帽。
–6–
拉出供⽔管 中的⽔泵 -
A
。
要重新安装，将⽔泵上的突出轮轴推⼊供⽔管 的边孔
-
A
。
Pull the pump out of the water supply pipe-A.
供⽔管-
A
Water Supply Pipe-A
with a sponge dampened with clean water.
Assemble pump assembly.
Pump impeller is made from magnet. The magnet will be attached to the
motor, so make sure there are not any foreign matters sticking on it.
Water
Supply
Pipe-A
-A
To re-install, push the axle protruding from the pump to the edged hole of the water supply pipe-A.
Lightly clean water supply pipe-A, pump impeller, pump box and pump cap
-
A