Toshiba GR 200 Series, Инструкция по эксплуатации

Страница: 957 / 1563

6F2S1915 (0.46)
GRZ200 (Soft 031 & 032)
- 936 -
5.4.4
Binary output circuit
Either a CPL logic or a PLC signal can drive a binary output circuit. Table 5.4-9 shows the
settings summary of CPL function.
Table 5.4-9 Setting items for binary output circuits
Setting items
Setting-range or
Data_ID
Uni
t
Contents Default
BO1_CPL Off / On – Switch On for programmable operation Off
BO1 Input signal1 (Preferred Data ID) – Set a Data ID at the first input on BO1. Not assigned
1
Input signal2 (Preferred Data ID) – Set a Data ID at the second input on BO1. Not assigned
1
Input signal3 (Preferred Data ID) – Set a Data ID at the third input on BO1. Not assigned 1
Input signal4 (Preferred Data ID) – Set a Data ID at the forth input on BO1. Not assigned
1
Input signal5 (Preferred Data ID) – Set a Data ID at the fifth input on BO1. Not assigned
1
Input signal6 (Preferred Data ID) – Set a Data ID at the sixth input on BO1. Not assigned 1
Input signal7 (Preferred Data ID) – Set a Data ID at the seventh input on BO1. Not assigned 1
Input signal8 (Preferred Data ID) – Set a Data ID at the eighth input on BO1. Not assigned
1
LOGIC-SW AND/OR/XOR – Switch for logic-gate operation on BO1 AND
On Delay Timer 0.000 to 300.000 s Set a value for an on-delay-timer on BO1 0.000
Off Delay Timer 0.000 to 300.000 s Set a value for an off-delay-timer on BO1 0.000
INVERSE-SW Normal / Inverse s Inversion operation of BO1 signal Normal
TIMER-SW OFF/Delay/Dwell/Latch – Selection of a type in the delay timer on BO1 OFF
Logic Timer 0.000 to 300.000 s Setting Off Delay Timer for Delay and Dwell 0.000
Reset signal (Preferred Data ID) – Setting Data ID for Latch Not assigned 1
BO2_CPL Off / On – Switch On for programmable operation Off
BO2 Input signal1 (Preferred Data ID) – Set a Data ID at the first input on BO2. Not assigned
1
….. ….. ….. …..
Input signal8 (Preferred Data ID) – Set a Data ID at the eighth input on BO2 Not assigned
1
LOGIC-SW AND/OR/XOR – Switch for logic-gate operation on BO2 AND
On Delay Timer 0.000 to 300.000 s Set a value for an on-delay-timer on BO2 0.000
Off Delay Timer 0.000 to 300.000 s Set a value for an off-delay-timer on BO2 0.000
INVERSE-SW Normal / Inverse – Inversion operation of BO2 signal Normal
TIMER-SW OFF/Delay/Dwell/Latch – Selection of a type in the delay timer on BO2 OFF
Logic Timer 0.000 to 300.000 s Setting Off Delay Timer for Delay and Dwell 0.000
Reset signal (Preferred Data ID) – Setting Data ID for Latch Not assigned
1
…..
BO
n
_CPL Off / On – Switch On for programmable operation Off
BO
n
Input signal1 (Preferred Data ID) – Set a Data ID at the first input on BO
n
Not assigned
1
….. ….. ….. …..
Input signal8 (Preferred Data ID) – Set a Data ID at the eighth input on BO n Not assigned
1
LOGIC-SW AND/OR/XOR – Switch for logic-gate operation on BO
n
AND
On Delay Timer 0.000 to 300.000 s Set a value for an on-delay-timer on BO
n
0.000
Off Delay Timer 0.000 to 300.000 s Set a value for an off-delay-timer on BO
n
0.000
INVERSE-SW Normal / Inverse – Inversion operation of BO n signal Normal
TIMER-SW OFF/Delay/Dwell/Latch – Selection of a type in the delay timer on BO
n
OFF
Logic Timer 0.000 to 300.000 s Setting Off Delay Timer for Delay and Dwell 0.000
Reset signal (Preferred Data ID) – Setting Data ID for Latch Not assigned 1
1
Note: The user can set a reset signal and eight input signals with Data IDs. Data IDs
are listed as a signal monitoring point for each function. Setting items are
summarized in each slot. (See sections 5.4.8(i) and 5.4.8(ii))