manualshive.com logo in svg

Toshiba G2020 Series, Инструкция по установке и эксплуатации, Страница: 40 / 86

Поделиться
Скачать
Toshiba G2020 Series Скачать руководство пользователя страница 40

 
 
 
 
 

32 

G2020 Series UPS Installation and Operation Manual 

– 94861-004 

These contacts can be programmed to provide any of the functions shown in Table 4-2.    The default programmed 

values are indicated with an asterisk (*). 

Table 4-2    External Output Functions 

Code 

Function 

Description 

0 

NONE 

 

1 * 

TOTAL ALARM 

Summary alarm; activated when any minor, major, fault or alarm has occurred with the 
system. 

This is the default setting on OUT8.

 

2 

MINOR FAULT 

Activated when a minor fault has occurred with the system. 

3 

ALARM 

Activated when an alarm has occurred with the system. 

4   

AC INPUT ABNORMAL 

Activated when the input voltage or frequency is abnormal. 

5 

BYPASS ABNORMAL 

Activated when the bypass voltage or frequency is abnormal. 

6   

BATTERY ABNORMAL 

Activated when the battery is abnormal. 

7 

BATTERY LOW VOLTAGE 1 

Activated when the battery voltage drops below Discharge Warning Voltage Level 1 during 
inverter operation.    This level is set in the TEST MENU by an Authorized Toshiba Service 
Provider. 

8 * 

BATTERY LOW VOLTAGE 2 

Activated when the battery voltage drops below Discharge Warning Voltage Level 2 during 
inverter operation.    This level is set in the TEST MENU by an Authorized Toshiba Service 
Provider. 

This is the default setting for OUT5.

 

9 

BATTERY DEPLETION 

Activated when the battery voltage drops below discharge end voltage level during inverter 
operation. 

10 * 

OVERLOAD 

Activated when an overload of 105% or more had occurred to the system.   

This is the default 

setting on OUT6.

 

11 

OVERLOAD PREALARM 

Activated when the load goes over 100%.    This level is adjustable by an Authorized Toshiba 
Service Provider. 

12 

FAULT GROUP 1 

Activated when the preset group of alarms (Fault Group 1) all occur to the system at once.   
These groups are set in the TEST MENU by an Authorized Toshiba Service Provider. 

13 

FAULT GROUP 2 

Activated when the preset group of alarms (Fault Group 2) all occur to the system at once.   
These groups are set in the TEST MENU by an Authorized Toshiba Service Provider. 

14 

BYPS. SYNCHRONOUS 

Activated when the inverter voltage and bypass voltage are synchronous. 

15 

BYPS. ASYNCHRONOUS 

Activated when the inverter voltage and bypass voltage are asynchronous. 

16 

REMOTE OPE. ENABLE 

Activated when any remote operation occurs (Stop/Start Inverter, etc.) 

17 * 

LOAD ON INVERTER 

Activated when the power is supplied from the inverter. 

This is the default setting on OUT2.

 

18 * 

LOAD ON BYASS 

Activated when the power is supplied from the inverter. 

This is the default setting on OUT1.

 

19 

LOAD ON AC 

Activated when the power is supplied from the input via the UPS's rectifier/converter - 
inverter.     

20 * 

BATTERY OPERATION 

Activated when the battery is operating following an AC power failure. 

This is the default setting on OUT3.

 

21 * 

CONVERTER OPERATION 

Activated when the converter is operating. 

This is the default setting on OUT4

 

22 

INVERTER OPERATION 

Activated when the inverter is operating. 

23 

CB1 CLOSE 

Activated when CB1 (Input Contactor) is closed. 

24 

CB2 CLOSE 

Activated when CB2 (Battery Breaker) is closed. 

25 

52S CLOSE 

Activated when 52S (Bypass Contactor) is closed. 

26 

POWER DEMAND ON 

Activated when a Power Demand is activated by one of the Inputs. 

27 

EQUALIZING CHARGE 

Activated when the UPS is charging the batteries at the equalizing charge level.    This 
command boosts the charge voltage (500-640 V) for a preset duration (0-100 hr.) 

28 

ANOTHER BUS SYNC.OK 

Annunciates that the UPS is successfully synchronized to an external source 

*Default output settings 

Содержание G2020 Series























































































Отзывы:

Нет отзывов