Toshiba E-Studio 5540c Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 118

background image

1.TROUBLESHOOTING FOR THE HARDWARE

Clearing a Paper Jam 41

1 TROUBLESHOOTING FOR THE HARDWARE

Clearing paper jams caused by a wrong paper type setting

Paper jams occur when there is a mismatch between the type of paper in a drawer and the one registered for the drawer
in the equipment. “Check paper type setting for drawer N” appears on the touch panel.

In this case, just clearing the jammed paper does not prevent another paper jam. Be sure to follow the procedure below.
Troubleshooting differs depending on how the paper jam has occurred:

P.41 “Jam when making copies or prints”

P.43 “Jam when printing from the FAX”

Jam when making copies or prints

1

Clear the paper jam following the guidance shown on the touch panel.

3

Close all the drawers or covers.

2

Open the paper source drawer, check that the guide
width is correct and there is no folded/curled paper or
overloading, and then close the drawer.

Be sure that the height of the stacked paper does not exceed the
line indicated inside of the side guides.

«
...
41
42
43
44
45
...
»

Содержание E-Studio 5540c























































































































Отзывы:

Нет отзывов

Похожие инструкции для E-Studio 5540c

imageCLASS Mf6160dw

Бренд: Canon Страницы: 64

imageCLASS MF6500 Series

Бренд: Canon Страницы: 132

imageCLASS MF5550

Бренд: Canon Страницы: 120

imageCLASS MF5630

Бренд: Canon Страницы: 85

imageCLASS MF5550

Бренд: Canon Страницы: 136

IMAGECLASS MF7400

Бренд: Canon Страницы: 40

imageCLASS MF5850dn

Бренд: Canon Страницы: 34

imageCLASS MF6500 Series

Бренд: Canon Страницы: 16

imageCLASS MF6540

Бренд: Canon Страницы: 82

imageCLASS MF5550

Бренд: Canon Страницы: 99

imageCLASS MF5630

Бренд: Canon Страницы: 24

imageCLASS MF5770

Бренд: Canon Страницы: 2

imagePRESS C7000VP Series

Бренд: Canon Страницы: 48

imageClass MF5650

Бренд: Canon Страницы: 40

imageCLASS MF5770

Бренд: Canon Страницы: 8

imageCLASS MF4880dw

Бренд: Canon Страницы: 36

imageCLASS MF4890dw

Бренд: Canon Страницы: 116

ImageCLASS MF4690

Бренд: Canon Страницы: 387

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды