August 2006
ELECTRICAL COMPONENTS
B700-33
Pe
riphe
ra
ls
No. Component
Function
paper output slot this sensor signals an error when it detects
(1) paper has failed to leave the paper exit (lag error), (2)
detects paper has failed to arrive at the paper exit (late error),
(3) detects paper is in the exit slot when the machine is
turned on.
S7
Exit Guide Plate HP
Sensor
Controls the vertical movement of the control exit guide . The
guide plate is in the home position when the guide plate is
down and the actuator interrupts the sensor gap.
S8 Upper
Tray
Paper
Height Sensor (Staple
Mode)
This is the upper sensor of the upper/lower paper height
sensor pair that controls the lift of the upper tray. This sensor
detects the paper height of the stack in the upper tray when
the copier is operating in the staple mode.
S9 Upper
Tray
Paper
Height Sensor (Non-
Staple Mode)
This is the lower sensor of the upper/lower paper height
sensor pair that controls the lift of the upper tray. When the
machine is switched on, the upper tray rises until the actuator
on the tray triggers this sensor to switch off the upper tray lift
motor.
S10
Proof Tray Exit Sensor
This sensor detects and times the feeding of paper to the
proof tray. It also detects whether paper is present at the
proof tray exit when the copier is switched on.
S11
Proof Tray Full Sensor
The top of the stack in the proof tray increases until it nudges
the feeler of this sensor. The sensor then signals that the
proof tray is full and the job halts until some paper is removed
from the proof tray.
S12
Upper Tray Limit Sensor
This sensor controls the position of the upper tray 1) during
straight-through feed out, 2) during shift feed out, 3) when the
machine is turned on. The machine obeys the signal of
whichever sensor is actuated first.
An actuator attached to an arm triggers this sensor. The tip of
the same arm depresses the upper tray limit switch If the
sensor fails, the tip of the arm will activate the upper tray limit
microswitch (SW2) and stop the lift of the upper tray.
Note: When the machine is turned on, the upper tray position
is controlled by either this sensor or the upper tray paper
height sensor (S9).
S13
Stacking Roller HP
Sensor
Controls the forward and back motion of the stacking roller (a
sponge roller) located at the output slot of the upper tray. The
sponge roller drags each ejected sheet back against the end
fence of the upper tray to keep the bottom of the stack
aligned.
S14 Stapling
Tray
Paper
Sensor
A photo sensor that detects whether paper is in the stapling
tray. When this sensor detects paper, the bottom fence motor
raises or lowers the bottom fence to position the selected
paper size for booklet stapling.
S15
Jogger Fence HP
Sensor
Detects the home position of the jogger fences. When the
actuator on the jogger fence interrupts this sensor, the jogger
fence is in its home position and the jogger fence motor
(M15) stops.
S16
Stack Feed-Out Belt HP
Sensor
Controls the position of the stack feed-out pawl on the stack
feed-out belt. Once the actuator on the feed belt nudges the
feeler of this sensor near the top of the stapler unit, the feed
out belt motor (M5) remains on for the time prescribed to
position the pawl at the home position to catch the next stack.
S17
Corner Stapler HP
Sensor
Located at the front the stapling tray and mounted above the
steel rod where the corner stapler travels, this sensor detects
Содержание e-STUDIO 4500c
