Toshiba Density (Consistency) Meter LQ500 Скачать руководство пользователя страница 1

Страница: 1 / 12

EJL- 106J

Density (Consistency) Meter LQ500

Introduction

The LQ500 density (%TS, consistency) meter uses
microwave phase shift technology to determine
concentrations of solids in the material to be measured
flowing through pipes. It can perform a stable and
realtime density (%TS, consistency) measurement
because this technology is not affected by flow velocity
along with fluid color, and also is not easily affected by
contaminants and low process pressure rate. As the
LQ500 has no moving parts, it is reliable and virtually
maintenance free.

Since the output of the LQ500 is theoretically linear, it
can be applied to a wide range of density (%TS,
consistency) measurement.

<Notice>

The LQ500 requires a full pipe to measure the
density (%TS, consistency). If certain amount of
bubbles are obviously mixed in measuring media,
there are possibilities of causing measuring error.
Contact Toshiba before installation in the
following cases:

<Possibility of unfilled condition>

(a) When it is installed at the discharge of a pump.

(b) When installation is horizontal, and unfilled

condition occurs inside the pipe.

(c) A process where the pipe becomes unfilled

when the operation is stopped.

Cable for power supply
(Detector/converter)

Ground resistance
100 ohm or less

Density (consistency)
measurement output
4-20mA

Cable for communication
(Detector/converter)

AC power supply

DI / DO

External Sync control
contact input

Figure

1. LQ500

Configuration

Diagram

Figure 2. LQ500 Density (%TS, consistency)

Meter

■

Standard Configuration

• Density (%TS, Consistency) Meter: 1 set

(Detector and converter separate mounted)

• Accessories: 1 set (see Table 1 below)

Table 1. Standard Accessories

Items

Specifications

Quantity

Power supply

cable

Between detector and

converter (*1)

10 m

(32.8 ft)

Communication

cable

Between detector and

converter (*1)

10 m

(32.8 ft)

Fuse

2A(T), 250 V

(glass tube, 5.2 dia. x 20 mm)

Document

Instruction manual

Note 1: Need to prepare a power supply cable for the LQ500.

Refer to the section of cable specifications at the
overall specifications in detail.

Содержание Density (Consistency) Meter LQ500













Результаты поиска

Содержание Density (Consistency) Meter LQ500

Отзывы:

Похожие инструкции для Density (Consistency) Meter LQ500

Бренды по названию

Популярные бренды

Toshiba Density (Consistency) Meter LQ500, Руководство по установке

Результаты поиска

Содержание Density (Consistency) Meter LQ500

Отзывы:

Похожие инструкции для Density (Consistency) Meter LQ500

Бренды по названию

Популярные бренды