Toshiba Camileo TDP-S20, Руководство по обслуживанию

Страница: 9 / 133

Operations
Using the menu
■
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Y
es”: displayed, “No”: not displayed
Item
Description
Computer
Y/P
B
/P
R
Video
Camera
S-video
Input
Input source name
Y
e
s
Y
es
Y
e
s
Y
es
Mode name
RGB input mode
[Note 1]
Ye
s
N
o
N
o
N
o
H-resolution
Horizontal resolution (in dots)
Y
e
s
No
No
No
V
-resolution
V
ertical resolution (in dots)
Y
e
s
N
o
N
o
N
o
H-frequency
Horizontal sync frequency
Y
e
s
No
No
No
V
-frequency
V
ertical sync frequency
[Note 2]
Ye
s
N
o
N
o
N
o
Sync
Sync signal polarity
[Note 3]
Ye
s
N
o
N
o
N
o
Signal format
Y/P
B
/P
R
signal format
No
Y
e
s
No
No
Video mode
Color method of video signal
No
No
Y
e
s
No
Lamp time
Time of lamp use
[Note 4]
Ye
s
Ye
s
Ye
s
Y
e
s
Lamp reset count
The count for lamp replacement
Y
e
s
Y
es
Y
e
s
Y
es
T
otal time
The total time that this projector is used
Ye
s
Y
e
s
Ye
s
Y
e
s
V
ersion
Firmware version
[Note 5]
Ye
s
Y
e
s
Ye
s
Y
e
s
Notes 1
:
The mode of supported RGB signals
is shown at owner's manual.
2
:
Same as the refresh rate of the computer signal.
3
:
Sync signal polarity shown as P
(positive) or N (negative) for [H/V].
4
:
Displays [
Lamp time
] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 3,000 hours, consult with a store about getting a
TLPL
V4 replacement lamp (sold separately) prepared.
5:
[
V
ersion
] shows the version of the projector
’s internal control program.
This version is referred
to for customer service, etc.
Note
•
The displayed information will not be refreshed if the status changes.
T
o refresh the
information, dismiss the display
, then display it again.
■
The default setting menu
This menu shows placement status and other settings.
Sets projection mode in accordance with Placement Style. Set the timer to w
ait f
or the po
w
er to be tur
ned off after signal input stops
.
Press .
Switch with and .
Off
(not tur
ned off)/
1 min.
/
5 min.
/
10 min.
/
30 min.
/
60 min.
Set whether the input with signals is only selected or not. Sets whether to tur
n on the po
w
er when the
ON/ST
ANDBY
b
utton is pressed
(Man
ual), or when the po
w
er cord is plugged in (A
uto).
Man
ual A
uto
Sets the lamp po
w
er
.
Sets the cooling f
an speed.
Press . Resets all adjustments and settings to their f
actor
y settings
.
Descr
iption
Item Pr
ojection
mode No signal po
wer off
A
uto input
sear
c
h
P
o
wer on
Lamp po
wer
[Note 1]
F
an mode
[Note 2]
Reset all
(Rear mounted from ceiling)
(Standard)
(Rear)
(Mounted from ceiling)
On Off
Standar
d High
Y
es No
Lo
w Standar
d
p.20
Notes 1:
When
Lamp power
is set to
Low
, the screen becomes a little darker
, but the cooling fan noise gets
quieter
.
This setting will be cleared when you turn the power of
f.
2:
Setting [
Fan mode
] to [
High
] increases the cooling fan speed. Set this option to use the projector
,
for example, at high altitude (over 1,500 meters above sea level).
Notes
•
Note that in the event of a power outage but the power is restored afterwards, the projector power will come on if
Power on
is set to
Auto
, and the power cord is plugged in.
•
When you turn of
f the projector even if
Power on
is set to
Auto
, you must press the
ON/
ST
ANDBY
button to turn the power of
f.
9
・
When Lamp time reaches in 3,000H, a Warning Display appears. Then, it is displayed every 100Hours.