Toshiba B-FP3D SERIES Скачать руководство пользователя страница 46

Страница: 46 / 46

B-FP3D Series Maintenance Manual

2-28

NOTES 2: Attached the assembly to the Lever strip.



Attach the assembly to the

Lever strip.

Step 5) Explanation has been changed.

2-29

Step 2) For the GH model, procedure for replacing the exclusive Bluetooth unit has

been added.

Take note of the clips.



Take care of the clips.

Step 3) Un-lock



Unlock

2-30

Step 4) For the GH model, procedure for attaching new adhesive tape to the

thermal head assembly has been added.

2-31

Step 2) For the GH model, procedure for replacing the exclusive WiFi unit has been

added.

Take note of the clips.



Take care of the clips.

2-32

Step 4) For the GH model, procedure for attaching new adhesive tape to the

thermal head assembly has been added.

Step D: Push the lock upwards



Pull the lock upwards

2-33

Add of chapter of rack and pinion gear installation procedure.

2-34

Step 3) Pull the PCB up



Pull the PCB upwards

3-1

Problem: The printer does not print media. (The status indicator blinks in red.)

“Open the media cover and close it again.” has been deleted from Solution No. 6, 7,

and 8.

Problem: The printer does not print media. (The status indicator lights in orange.)

“Turn off the printer and” has been added.

Version: 0003

Page

Contents

2-33

2.12.1 Country/Region Code Switching Method for WiFi Module for B-FP3D-GH52

has been newly added.

This addition caused the page numbers of Sections 2.13 and 2.14 to shift.

Содержание B-FP3D SERIES















































Результаты поиска

Содержание B-FP3D SERIES

Отзывы:

Бренды по названию

Популярные бренды

Toshiba B-FP3D SERIES, Руководство по обслуживанию

Результаты поиска

Содержание B-FP3D SERIES

Отзывы:

Бренды по названию

Популярные бренды