background image

7

Toshiba 1110651160 (EN)

A

B

OTHERS

Gas Leak Test

Remote Control A-B Selection

“B” Display

“00” Display

To separate using of remote control for each indoor unit in case of  air 

conditioners are installed near.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.

. Point the remote control at the indoor unit.

3. Push and hold 

 button on the Remote Control by the tip of the pencil. 

“00” will be shown on the display.

4. Press 

 during pushing 

. “B” will show on the display and “00” will 

disappeared and the air conditioner will turn OFF. The Remote Control B 

is memorized.

Note  :  1. Repeat above step to reset Remote Control to be A.

 

  . Remote Control A have not “A” display.

 

  3. Default setting of Remote Control from factory is A.

 Check the fl are nut connections, valve stem cap connections and service 

port cap connection for gas leak with a leak detection or soap water.

Model

18 Class

24 Class

Power source

50Hz, 0 – 30 V Single phase

Maximum running current

16A

18A

Plug socket & fuse rating

0A

0A

Power cord

4 mm

 (H07RN-F or 6045 IEC66) 

or 3.5 mm

 (AWG-1)

70

L N

10

60

10

70

10

80

10

1 2 3

L

N

1

3

2

Terminal block

Earth line

Cord clamp

Earth line

Terminal screw

Cord clamp

Screw

Power supply cord

Connecting cable

Power supply cord

Connecting cable

100

60

L N

10

70

10

80

10

1 2 3

10

Earth line

Power supply cord

Connecting cable

L

N

1

3

2

Terminal block

Cord clamp

Earth line

Terminal screw

Cord clamp

Screw

Power supply cord

Connecting cable

For 18 Class

For 24 Class

Earth line

Stripping length of the connecting cable

CAUTION

 Wrong wiring connection may cause some electrical parts burn out.

 Be sure to comply with local rule on running the wire from indoor unit 

to outdoor unit (size of wire and wiring method, etc.).

 Every wire must be connected fi rmly.

 If incorrect or incomplete wiring is carried out, it will cause an ignition 

or smoke.

 Prepare the power supply for exclusive use with the air conditioner.

 This product can be connected to the mains.

  Connection to fi xed wiring : A switch which disconnects all poles and 

has a contact separation of at least 3 mm must be incorporated in the 

fi xed wiring.

NOTE 

:  Connecting cable

 Wire type  :  More than 1.5 mm

 (H07RN-F or 6045 IEC66) or 1.3 mm

    

 

  (AWG-16) 

Service port cap connection

Valve stem cap connection

Flare nut connections

(Outdoor unit)

Flare nut connections 

(Indoor unit)

Valve stem cap connection

PRESET

FAN

 When two indoor units are installed in the same room or adjacent two 

rooms, if operating a unit, two units may receive the remote control 

signal simultaneously and operate. In this case, the operation can be 

preserved by setting either one remote control to B setting. (Both are 

set to A setting in factory shipment.)

 The remote control signal is not received when the settings of indoor 

unit and remote control are different.

 There is no relation between A setting/B setting and A room/B room 

when connecting the piping and cables.

Содержание 24S Series











Отзывы: