TORREY PINES SCIENTIFIC EchoTHerm RIC40 Скачать руководство пользователя страница 3

Torrey Pines Scientific, Inc. 

 

I. INTRODUCTION 

 

Congratulations on your purchase of a 

EchoTherm

 TM

 Remote Controlled Chilling/Heating 

Dry Bath Model RIC40.  Please read the instructions carefully to insure that you receive the 
maximum benefit from it.  Also, be sure to go to our web site and register your unit for 
warranty coverage.  When users in the USA and Canada do they will receive a Torrey 
Pines Scientific, Inc. T-Shirt free. 
 
 

II. WARRANTY 

 

Torrey Pines Scientific warrants this product to be free from defects in  material and 
workmanship for a period of one year from the date of purchase.  If repair or adjustment is 
necessary and has not been the result of abuse or misuse within the one year period, 
please return---freight prepaid---and correction of the defect will be made without charge. 
Out of warranty products will be repaired on a charge basis. 
 
 

III. RETURN OF ITEMS 

 

Authorization must be obtained from our Customer Service Department before 
returning items for any reason.  

When applying for authorization, please include data 

regarding the reason the items are to be returned.  For your protection, items must be 

carefully packaged

 to prevent damage in shipment and 

insured

 against possible damage 

or loss.  Torrey Pines Scientific will not be responsible for damage resulting from careless 
or insufficient packing.  A 15% restocking charge will be made on all unauthorized returns. 
 

Note: 

Torrey Pines Scientific reserves the right to make improvements in design, 

construction, and appearance without notice. 
 

IV. LABELS 

 
There are various labels on the body of this unit.  Listed below are the labels and their 
meanings. 
 

 
This symbol means: ATTENTION.  The INSTRUCTION MANUAL IS TO 
BE CONSULTED FOR FURTHER INFORMATION 

 

 
 
This symbol means: WARNING. HOT SURFACE. 
 

 

 
This symbol means: GROUND OR EARTH CONNECTIONS 

Содержание EchoTHerm RIC40






























Отзывы: