Toro Z14-38 TimeCutter Z 74402 Скачать руководство пользователя страница 12

12

Gasoline and Oil

Recommended Gasoline

Use UNLEADED Regular Gasoline suitable for automotive
use (87 pump octane minimum). Leaded regular gasoline
may be used if unleaded regular is not available.

Important

 

Never use methanol, gasoline containing

methanol, or gasohol containing more than 10% ethanol
because the fuel system could be damaged. Do not mix oil
with gasoline.

Danger

In certain conditions, gasoline is extremely
flammable and highly explosive. A fire or
explosion from gasoline can burn you and others
and can damage property.

Fill the fuel tank outdoors, in an open area,
when the engine is cold. Wipe up any gasoline
that spills.

Never fill the fuel tank inside an enclosed trailer.

Do not fill the fuel tank completely full. Add
gasoline to the fuel tank until the level is 1/4 to
1/2 inch (6 to 13 mm) below the bottom of the
filler neck. This empty space in the tank allows
gasoline to expand.

Never smoke when handling gasoline, and stay
away from an open flame or where gasoline
fumes may be ignited by a spark.

Store gasoline in an approved container and
keep it out of the reach of children. Never buy
more than a 30-day supply of gasoline.

Always place gasoline containers on the ground
away from your vehicle before filling.

Do not fill gasoline containers inside a vehicle or
on a truck or trailer bed because interior
carpets or plastic truck bed liners may insulate
the container and slow the loss of any static
charge.

When practical, remove gas–powered
equipment from the truck or trailer and refuel
the equipment with its wheels on the ground.

If this is not possible, then refuel such
equipment on a truck or trailer from a portable
container, rather than from a gasoline dispenser
nozzle.

If a gasoline dispenser nozzle must be used, keep
the nozzle in contact with the rim of the fuel
tank or container opening at all times until
fueling is complete.

Gasoline is harmful or fatal if swallowed.
Long–term exposure to vapors can cause serious
injury and illness.

Avoid prolonged breathing of vapors.

Keep face away from nozzle and gas tank or
conditioner opening.

Keep gas away from eyes and skin.

Warning

Using Stabilizer/Conditioner

Use a fuel stabilizer/conditioner in the machine to provide
the following benefits:

Keeps gasoline fresh during storage of 90 days or less.
For longer storage it is recommended that the fuel tank
be drained.

Cleans the engine while it runs

Eliminates gum-like varnish buildup in the fuel system,
which causes hard starting

Important

 

Do not use fuel additives containing

methanol or ethanol.

Add the correct amount of gas stabilizer/conditioner to the
gas.

Note: A fuel stabilizer/conditioner is most effective when
mixed with fresh gasoline. To minimize the chance of
varnish deposits in the fuel system, use fuel stabilizer at all
times.

Filling the Fuel Tank

1. Shut the engine off and set the parking brake.

2. Clean around the fuel tank cap and remove the cap. Add

unleaded regular gasoline to the fuel tank until the level
is 1/4 to 1/2 inch (6 to 13 mm) below the bottom of the
filler neck. This space in the tank allows gasoline to
expand. Do not fill the fuel tank completely full.

3. Install the fuel tank cap securely. Wipe up any gasoline

that may have spilled.

Checking the Engine Oil Level

Before you start the engine and use the machine, check the
oil level in the engine crankcase; refer to Checking the Oil
Level, page 23.

Содержание Z14-38 TimeCutter Z 74402









































Отзывы: