manualshive.com logo in svg

Toro Z Master Series, Инструкции по установке

Поделиться
Скачать
Toro Z Master Series Скачать руководство пользователя страница 11

15

Installing the ROPS Hardware
(LPG Machines Only)

Parts needed for this procedure:

1

Bolt (1/2 x 3-1/4 inch)

1

Locknut (1/2 inch)

Procedure

Install the bolt (1/2 x 3-1/4 inch) and locknut (1/2 inch)
into the open hole in the Roll-Over Protection System
(ROPS)—

Figure 25

. This will prevent the roll bar from

hitting the cylinder when lowered to the down position.

G013506

1

2

3

Figure 25

1.

Locknut (1/2 inch)

3.

Bolt (1/2 x 3-1/4 inch)

2.

ROPS

16

Installing the ROPS
(International Machines
Using Gasoline Only)

Parts needed for this procedure:

1

Roll-Over Protection System (ROPS) Kit

Procedure

Install the Roll-Over Protection System (ROPS) Kit. Follow
the instructions included with the ROPS Kit.

17

Installing the ROPS (Diesel
Machines Only)

Parts needed for this procedure:

1

Roll bar, right section

1

Roll bar, left section

1

Roll bar, center section

8

Bolt (3/8 x 1 inch)

8

Curved washer

8

Flange nut (3/8 inch)

2

Bolt (1/2 x 3–1/4 inch)

2

Flange nut (1/2 inch)

Procedure

1.

Loosely install the right and left roll bar section to the
frame, with 8 bolts (3/8 x 1 inch), 8 curved washers,
and 8 flange nuts (3/8 inch).

Note:

Install the curved washer cone toward the bolt

head.

11

 

Содержание Z Master Series

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды