Toro TITAN ZX6020 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 60

Toro TITAN ZX6020 Скачать руководство пользователя страница 47

5.

Loosen the leveling adjust locking nuts (item 3) on all
four corners so that the deck is sitting securely on all
four blocks (Figure 66 and Figure 67).

G020324

1

2 3

4

1

6

5

3

Figure 66

48 and 54 inch Mower Decks

1.

Deck lift arm

4.

Slot in deck hanger

2.

Deck hanger

5.

Slot in rear deck hanger
bracket

3.

Leveling adjust locking nut

6.

Rear deck hanger bracket

G020326

1

2 3

1

2

3

4

4

Figure 67

60 inch Mower Decks

1.

Deck lift arm

3.

Leveling adjust locking nut

2.

Deck hanger

4.

Slot in deck hanger

6.

Ensure that the deck hangers are all the way down (at
the top of the slot) and the deck lift foot lever is pushed
back against the stop (Figure 66 and Figure 67).

7.

Tighten the four leveling adjust locking nuts
(Figure 66 and Figure 67).

8.

Check that blocks fit just snugly under the deck skirt.
Make sure all attachment bolts are tight

9.

Verify that the deck is level by checking the side-to-side
level and front-to-rear blade slope; repeat the deck
leveling procedure if necessary.

Inspecting the Belts

Service Interval:

Every 50 hours

Check the belts for squealing when the belt is rotating, blades
slipping when cutting grass, frayed belt edges, burn marks and
cracks are signs of a worn mower belt. Replace the mower
belt if any of these conditions is evident.

Replacing the Mower Belt

WARNING

The spring is under tension when installed and can
cause personal injury.

Be careful when removing the belt.

Removing the Belt

Squealing when the belt is rotating, blades slipping when
cutting grass, frayed belt edges, burn marks and cracks are
signs of a worn mower belt. Replace the mower belt if any of
these conditions is evident.

1.

Disengage the blade control switch (PTO), move the
motion control levers to the neutral locked position,
and set the parking brake.

2.

Stop the engine, remove the key, and wait for all moving
parts to stop before leaving the operating position.

3.

Lower the mower to the 76 mm (3 inch) height-of-cut
position.

4.

Remove the belt covers (Figure 68).

47

«
...
45
46
47
48
49
...
»

Содержание TITAN ZX6020





























































Отзывы:

Нет отзывов