manualshive.com logo in svg

Toro TITAN ZX 74846, Инструкции по установке

Поделиться
Скачать
Toro TITAN ZX 74846 Скачать руководство пользователя страница 6

5

Checking the Mower
Adjustment

No Parts Required

Procedure

Adjust the side-to-side level and the front-to-rear blade slope.
Use the relevant procedures in the

Operator's Manual

to verify

that the deck is level, and make any adjustments as necessary.
Refer to the

Operator's Manual

for more information.

6

Completing the Setup

Parts needed for this procedure:

1

Ignition key

1

Operator's Manual

1

Engine

Operator's Manual

Procedure

Checking the Tire Pressure

Check the front and rear tires for proper inflation; refer to
Checking the Tire Pressure in the

Operator's Manual

for the

recommended inflation pressure.

Checking the Side-Discharge Chute

Remove the packing restraint holding the side discharge chute
up and lower the chute into place.

Checking the Engine-Oil Level

Before you start the engine and use the machine, check the
oil level in the engine crankcase; refer to Checking the Oil
Level in the

Operator's Manual

.

Keep all the following items with the machine:

•

Ignition key

•

Operator's Manual

•

Engine Operator's Manual

6

 

Содержание TITAN ZX 74846









Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды